Vaddio 998-9100-200 User Manual

Displayed below is the user manual for 998-9100-200 by Vaddio which is a product in the Security Camera Accessories category. This manual has pages.

Related Manuals

Vaddio Groupstation Premier System Manual

Vaddio 535-2000-217 Manual

Vaddio 535-2000-219 Manual

Vaddio 535-2000-221 Manual

Vaddio 535-2000-232 Manual

Vaddio 535-2000-234 Manual

Vaddio 535-2000-291 Manual

Vaddio 535-2000-296 Manual

VADDIO™ DOMEVIEW™ HD

INDOOR PENDANT MOUNT DOME ENCLOSURE FOR THE VADDIO

ROBOSHOT™ AND HD-SERIES PTZ CAMERAS

Part Number: 998-9100-200

(Camera not included)

Installation and User Guide

DomeVIEW HD - 12” Indoor Pendant Mount Dome

DomeVIEW HD - 12” Indoor Pendant Mount Dome Manual 342-0187 Rev. B Page 2 of 8

Inside Front Cover - Mostly Blank

DomeVIEW HD - 12” Indoor Pendant Mount Dome

DomeVIEW HD - 12” Indoor Pendant Mount Dome Manual 342-0187 Rev. B Page 3 of 8

Overview:

The Vaddio 12” DomeVIEW HD Series Dome Enclosures

for the ClearVIEW™ HD-18, HD-19, HD-20,

PowerVIEW™ HD-22, HD-30, HD-USB, HD-19SE and

RoboSHOT PTZ cameras are attractive and robust

integrated HD security solutions for indoor and light-duty

outdoor applications. The DomeVIEW HD Series offers

three distinctly different products. In all cases, the

cameras are not included. This manual covers the 12”

Indoor Pendant Mount Dome Enclosure.

Each Indoor Pendant Mount Dome Enclosure includes a

clear 12” optical-grade polycarbonate dome, metal back

can, UV protected plastic shroud and mounting hardware

(see parts explosion on next page).

The 1.5” NPT pipe adapter attached to the top of the dome

and is anchored through the plastic shroud, metal back

can with a gasket for a strong and tight top seal.

Accessories include a Wall Mount Kit, a Wall Mount with

Pole Mount Kit (for poles 3” to 10” / 76.2mm to 254mm)

and a Structure Mounting Box Kit which uses a 1.5” NPT

thread adapter.

The DomeVIEW HD Series Domes are an excellent way

to securely mount Vaddio PTZ cameras for a wide range

of HD video applications.

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested

for use indoors, and with the provided power supply and cabling. The use of a power supply other than the one

provided or outdoor operation has not been tested and could damage the device and/or create a potentially unsafe

operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.

In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,

do not immerse in water or other liquids and avoid extremely humid conditions.

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are

misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product

drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from

www.vaddio.com free of charge.

Use only the power supply provided with any camera system. Use of an y

unauthorized or extended power supply will void any and all w arranties.

Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not

work well for professi onal installations and can be the c ause of intermittent connecti ons which

can result in the RS-232 control line failing and locking up, and/or compromising the HSDS™

signals. For best results please use standard RJ-45 connectors and test all cables for proper pin-

outs

rior to use and c onnection to Vaddio

roduct.

12” Indoor Pendant Mount Dome (with Clear Optical-

Grade Dome (shown with 1.5” NPT Pipe and HD-18

Camera - Camera Not Included)

DomeVIEW HD - 12” Indoor Pendant Mount Dome

DomeVIEW HD - 12” Indoor Pendant Mount Dome Manual 342-0187 Rev. B Page 4 of 8

Anatomy of the 12” Indo or Pendant Mount Dome:

The DomeVIEW HD Indoor Pendant Mount Dome Enclosure will come partially assembled.

 1.5” NPT Pipe Flange: Fits 1.5” NPT pipe or wall

mount kit with 1.5” NPT male threads*

 Rubber gasket to seal between pipe flange

and plastic shroud*

 UV protected plastic

shroud with drip edge*

 Three (3) 10-32 x .5” pan head screws attach

through back of metal back can to the 2.5”

stand-offs*

 Four (4) ¼’-20 Keps Nuts secure the 1.5” NPT

pipe flange to the enclosure*

 Sealed metal back can with weather

stripping sealer around flange*

 Two ¼”-20 x 5/8” screws attach HD-18/19 camera to platform

 Two ¼”-20 x 3/8” screws attach HD-19SE/20/22/30/USB and

RoboSHOT camera to platform

 Universal Camera Platform

 Three (3) 10-32 x .5” Pan Head Screws

attach through the camera platform to the

2.5” stand-offs*

 Vaddio HD-20 or HD-18 PTZ Camera

 12” Smoke tinted dome with three (3)

stainless steel screws attached

These parts are pre-assembled.

Not Assembled

Stand-offs:

 Three (3) 2.5” long 10-32 threaded F to F 0.5” Hex stand-offs support

the camera platform* for HD-18 & HD-19 Cameras

 Three (3) 0.75” long 10-32 threaded M to F 0.5” Hex stand-off

extensions, add to 2.5” stand-offs for use with HD-19SE,20/22/30 & HD-

USB Cameras Only

 Three (3) 4.0” long 10-32 threaded F to F, 0.5” Hex stand-offs. Use only

”

sta

r R

oboS

DomeVIEW HD - 12” Indoor Pendant Mount Dome

DomeVIEW HD - 12” Indoor Pendant Mount Dome Manual 342-0187 Rev. B Page 5 of 8

Unpacking:

Unpack and identify the following parts for 999-9100-200

DomeVIEW HD - Indoor Pendant Mount Dome Enclosure Package includes:

 One (1) Dome Enclosure Assembly with the following parts:

 One (1) 1.5” NPT Pipe Flange

 One (1) Rubber Gasket (to seal between pipe flange and plastic shroud)

 One (1) UV Protected Plastic Enclosure Shroud

 One (1) Universal Camera Platform

 Three (3) 10-32 x .5” Pan Head Screws (attach through metal back can to the 2.5” stand-offs)

 One (1) Sealed Metal Back Can (with weather stripping sealer around flange)

 Four (4) ¼’-20 Keps Nuts (secures the 1.5” NPT pipe flange to the enclosure)

 Three (3) 2.5”, 10-32 Threaded F to F .5” Hex Stand-offs (supports the camera platform for HD-18/19)

 Three (3) 10-32 x .5” Pan Head Screws (attach the camera platform to the stand-offs)

 Three (3) .75” Long 10-32 Threaded M to F .5” Hex Stand-off Extensions (for HD-19SE/20/22/30 & HD-USB

cameras using the 2.5” stand-offs with the .75” stand-off extensions)

 Three (3) 4.0” Long 10-32 Threaded F to F .5” Hex Stand-offs (supports the camera platform for RoboSHOT)

 Two ¼”-20 x 5/8” Screws (attach HD-18 and HD-19 camera to platform)

 Two ¼”-20 x .3/8” Screws (attach HD-20 camera to platform) - do not use 5/8” Screws on HD-20/22/30

 12” Optical-Grade Clear Dome with Three (3) Stainless Steel Screws Attached

Other things that are needed for system completion:

 One (1) Vaddio HD PTZ Camera Package

 1.5” NPT Wall Mount, Structure Mount or 1.5” NPT Threaded Pipe (see Accessories - sold separately)

Note: The 12” Smoke Tinted Dome can be purchased as an accessory for use indoors.

Conveniently Located Accessory Section:

998-9000-210: 12” (304.5mm) Clear Dome Accessory

 Includes Clear Dome with Stainless Steel Screws

998-9000-220: 12” (304.5mm) Smoke Tinted Dome Accessory

 Includes Smoke Tinted Dome with Stainless Steel Screws

998-9300-000: Wall Mount Kit for Pendant Mount Domes

 Heavy duty aluminum cast construction

 1.5” NPT threads easily onto domes

998-9300-001: Wall Mount with Pole Mount Kit for Pendant Domes

 Heavy duty aluminum cast construction

 1.5” NPT threads easily onto domes

 Accommodates 3” (7.62cm) to 10” (25.4cm) poles

998-9300-002: Structure Mounting Box Kit for Pendant Domes

 Mounting box with heavy duty 1.5” NPT thread adapter

 Requires 1.5” NPT pipe (not supplied)

DomeVIEW HD - 12” Indoor Pendant Mount Dome

DomeVIEW HD - 12” Indoor Pendant Mount Dome Manual 342-0187 Rev. B Page 6 of 8

Pre-Installation:

 Before starting the installation of the DomeVIEW HD 12” Indoor Pendant Mount Dome Enclosure, please read

this manual. There are several things to consider before mounting a dome.

 When locating the dome, consider camera and subject matter viewing angles, lighting conditions, possible line

of site obstructions and check for construction challenges where the camera is to be mounted. Pick a mounting

location to optimize the performance of the camera. Avoid locating lighting elements or direct sunlight.

 Vaddio HD and RoboSHOT Series PTZ cameras use Cat-5e cable for video power and control. When

terminating the Cat-5e cabling, please make sure that each cable is marked and tested for proper termination

of all ends with a continuity tester. Please do not use the “pass -thru” type RJ-45 connectors.

 All work must conform to local building codes and should be performed by qualified

personnel. For the most obvious reasons, a ladder is required to install the DomeVIEW

HD Enclosure. Safety comes first, so please use safe tools, ladders and installation

practices.

 Always measure twice, and check your work, then cut once.

STEP-BY-STEP Installation Instructions:

Step 1:

It is easiest to mount the dome on the 1.5” NPT pipe mount or wall mount and then install the contents of the dome

to avoid cabling problems as the dome is spun onto the pipe mount. Rotate the dome counter-clock wise until

threads are fully engaged.

Note: The camera and contents can also be installed on the ground, but extra care must be taken with the cables

when the dome is spun onto the 1.5” NPT pipe threads - Installer’s preference.

Step 2:

Loosen the two (2) 10-32 x .375” screws on the Universal Platform that are key-holed and fully remove one (1) 10-

32 x .375” screw from the camera platform. Slide the two loosened screws through the keyholes and remove the

platform.

Step 4:

Pull the camera’s Cat-5e cabling through the 1.5” NPT pipe at this time.

Step 5:

Using the provided ¼”-20 x 5/8 screws, attach the HD-18 or HD-19 camera to the camera platform.

NOTE #1: If using the HD-19SE/20/22/30/USB camera, take the thee (3) .75” long 10-32 threaded M to F .5” Hex stand-off

extensions and attach them to the Three (3) 2.5” long 10-32 threaded F to F .5” Hex stand-offs in the bottom of the dome’s tub.

Tighten the hex stand-offs firmly with a socket or nut driver. Attach the HD-20 camera with the provided ¼”-20 x 3/8” screws to

the Camera Platform.

NOTE #2: If using the RoboSHOT Series cameras, remove the installed Three (3) 2.5” long 10-32 threaded stand-offs from the

dome’s tub, and replace with Three (3) 4.0” long stand-offs. This will compensate for the height difference of the RoboSHOT’s

spatially efficient design. Attach the camera with the provided ¼”-20 x 3/8” screws to the Camera Platform.

Step 6

Set the camera dip and rotary switches (functions and video resolutions prior to installing it in the dome). Re-install

the Universal Mounting Platform inside the dome with the camera attached. Slip the keyholes over the screws in

the stand-offs and tighten down all three platform screws Connect the Cat-5e cables according to the manual that

was included with the camera package purchased, making sure the cables are tucked up behind the mounting plate

to avoid interference with the PTZ camera movement.

Step 7:

Once the camera is installed in the dome, pull the cable slack back through the pendant extension pipe or curved

wall mount.

DomeVIEW HD - 12” Indoor Pendant Mount Dome

DomeVIEW HD - 12” Indoor Pendant Mount Dome Manual 342-0187 Rev. B Page 7 of 8

Step 8:

Attach the 12” polycarbonate dome to the enclosure with the three (3) attached stainless steel screws.

Step 9:

Connect the camera at the head end according to the camera manual.

NOTE: Check all the marked Cat-5e cables for continuity in advance of the final connection.

Plugging the Cat-5e cables into the wrong RJ-45 jack may cause damage to the camera

system and void the warranty .

Warranty Information

(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):

Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants

its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to

the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will repair or replace

products that prove to be defective. Vaddio manufactures its hardware products from parts and components that are new or

equivalent to new in accordance with industry standard practices.

Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the customer,

customers applied software or interfacing, unauthorized modifications or misuse, mishandling, operation outside the normal

environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site operation

and maintenance. OEM products and products manufactured by other companies are excluded and are covered by the

manufacturer’s warranty.

Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under

warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor

charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for

testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.

Vaddio Technica l Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or

replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at

support@vaddio.com or online at vaddio.com.

Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from

Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product serial

numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of purchase. See

the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be issued to Vaddio

dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in all correspondence

with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the product. All products

returned for credit are subject to a restocking charge without exception.

Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been

disassembled or damaged through misuse, accident, modifications, use of incorrect power supply, use of a modified power

supply or unauthorized repair.

Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any

responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance

charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound freight carrier. If

the return shipment appears damaged, retain the original boxes and packing material for inspection by the carrier. Contact your

carrier immediately.

Products not under Warranty : Payment arrangements are required before outbound shipment for all out of warranty products.

Other General Information:

Care and Cleaning

Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

 Do not spill liquids in the product

 Keep this device away from food and liquid, especially caviar.

 For smears or smudges on the product, wipe with a clean, soft cloth

 Do not use any abrasive chemicals on domes.

Operating and Storage Conditions:

Do not store or operate the device under the following conditions:

 Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)

 High humidity, condensing or wet environments

 In swimming pools with movie stars

 In inclement weather

 Dry environments with an excess of static discharge

 In, under or around basement laundry tubs

 Under severe vibration

DomeVIEW HD - 12” Indoor Pendant Mount Dome

DomeVIEW HD - 12” Indoor Pendant Mount Dome Manual 342-0187 Rev. B Page 8 of 8

131 Cheshire Lane Suite 500, Minnetonka, MN 55305

Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464

www.vaddio.com

change without notice. Vaddio, ClearVIEW, PowerVIEW, DomeVIEW, and RoboSHOT are registered trademarks of Vaddio. All other trademarks are

property of their respective owners. Document Number 342-0187 Rev. B, SD: 68311.5