Vaddio 998-9300-001 User Manual
Displayed below is the user manual for 998-9300-001 by Vaddio which is a product in the Mounting Kits category. This manual has pages.
Related Manuals
Camera and Electronic Products for Integrators
2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited.
Specifications and pricing subject to change. Vaddio and DomeVIEW are registered trademarks of Vaddio. Document 341-446, Page 1 of 2
Installation and User Guide
Curved Wall Mount and Pole Mount Kit
For DomeVIEW™ Indoor and Outdoor Pendant Mount Domes
Wall Mount Kit 998-9300-000
Wall Mount with Pole Mount Kit 998-9300-001
Installation (Curved Wall Mount 998-9300-000 Only)
1. Carefully unpack box, inspect contents for damage and verify that all components are included.
2. Attach the mount to the wall, using the appropriate fasteners (not included) for the mounting surface.
3. Route power and video leads through mount by pulling enough length to reach into the housing.
4. Attach the dome 1-½” NPT fitting to the wall mount and lock into place with the provided 1-½” NPT lock nut.
5. Refer to the housing instruction sheet to complete the installation (see Figure 1).
Installation (Curved Wall Mount and Pole Mount Kit - 998-9300-001)
1. Carefully unpack box, inspect contents for damage and verify that all components are included.
2. Feed the stainless bands through the slots and attach the mount to the pole firmly by tightening the bands with a
screwdriver (see Figure 2).
3. Install the Curved Wall Mount by attaching the wall mount to the Pole Mount with the bolts provided. Make sure
that the mount is level and tighten all four (4) bolts firmly. Run the cabling, pulling enough length through to
reach into the housing without strain.
4. Seal the wire passage with silicone sealant (not included). Provide a drip loop if the cable entry is from the top.
5. Attach the dome 1-½” NPT fitting to the wall mount and lock into place with the provided 1-½” NPT lock nut.
6. Refer to the housing instruction sheet to complete the installation.
Figure 1:
Curved Wall Mount for Indoor and Outdoor Pendant Domes
Vaddio Part # 998-9300-000
Curved Wall Mount comes with:
One (1) Curved Wall Mount
(No other screws or accessories are included)
Dimensions:
Mounting Plate (H x W) - 7.5” (19.05cm) x 4.5” (11.43cm)
Distance from Wall - 10.5” (26.67cm) to center of pipe
Height - 9.5” (24.13cm)
Figure 2:
Curved Wall Mount and Pole
Mount Adapter for Indoor and
Outdoor Pendant Domes
Vaddio Part # 998-9300-001
Pole Mount Kit comes with:
One (1) Pole Mount Adapter Plate
Four (4) Stainless Steel Bolts
Two (2) Steel bands with clamps
Dimensions:
Mounting Plate (H x W) – 7.5”
(19.05cm) x 5.25” (13.34cm)
Back Flange - 2” (5.08cm) Deep
Vaddio, 4800 Quebec Avenue North, Minneapolis, MN 55428 (763)-537-3601, www.vaddio.com,
Document 341-446, Page 2 of 2
SAVE THESE INSTRUCTIONS:
The information contained in this manual will help you install your Vaddio DomeVIEW product. If these instructions
are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the website. These documents can be downloaded from www.vaddio.com
free of charge.
WARRANTY INFORMATION:
Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product against defects in
materials and workmanship for a period of one year from the day of purchase if Vaddio receives notice of such
defects during the warranty. They will, at its option, repair or replace products that prove to be defective.
Exclusions - The above warranty shall not apply to defects resulting from: improper or inadequate maintenance by
the customer, customers applied software or interfacing, unauthorized modifications or misuse, operation outside the
normal environmental specifications for the product, use of the incorrect power supply, or improper site operation and
maintenance.
Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if the unit is
under warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts
and labor charge will be estimated by a technician and confirmed by the customer prior to repair. All components
must be returned for testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the
premises.
Vaddio Technical support - Vaddio technicians will determine and discuss with the customer the criteria for repair
costs and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail
support at support@vaddio.com or online at www.vaddio.com.
Return Material Authorization (RMA) number - Before returning a product for repair or replacement request an
RMA from Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping
address, and product serial numbers. Describe the reason for repairs or returns as well as the date of purchase.
Include your assigned RMA number in all correspondence with Vaddio. Write your assigned RMA number on the
outside of the box when returning the product.
Voided warranty – The warranty does not apply if the original serial number has been removed or if the product has
been disassembled or damaged through misuse, accident, modifications, or unauthorized repair.
Shipping and handling - Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges all items under warranty but will not assume responsibility for loss and/or damage by the outbound
freight carrier. If the return shipment appears damaged, retain the original boxes and packing material for inspection
by the carrier. Contact your carrier immediately.
Products not under warranty - Payment arrangements are required before outbound shipment for all out of
warranty products.
*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with
industry standard practices.