Table of Contents
- Overview
- Unpacking the OneLINK Bridge AV Interface
- A Quick Look at the OneLINK Device
- Installing the OneLINK Device
- Powering Up the Equipment
- Configuration and Administration Tasks
- Compatible Web Browsers
- Accessing the Web Interface
- Web Interface Cheat Sheet
- Configuring Network Settings
- Assigning a Hostname
- Specifying Time Zone and NTP Server
- Managing Access and Passwords
- Adding Room Information to the Web Interface
- Configuring Streaming Settings
- Enabling Phantom Power to Microphones
- Configuring Audio Settings
- Viewing System Information
- Saving (Exporting) or Restoring (Importing) a Configuration
- Rebooting the OneLINK Device
- Restoring Factory Settings
- Starting a Firmware Update
- Contacting Vaddio Technical Support and Viewing Diagnostics
- Telnet Serial Command API
- Specifications
- Troubleshooting
- Compliance Statements and Declarations of Conformity
- Warranty Information
- Index
Vaddio 999-9670-001 User Manual
Displayed below is the user manual for 999-9670-001 by Vaddio which is a product in the AV Conferencing Bridges category. This manual has pages.
Related Manuals
Integrator's Complete Guide to the
OneLINK Bridge
AV Interface
Document 411-0009-30 Rev C
February 2018
ii
Contents
Overview 1
What's in this Guide 2
Features 2
Unpacking the OneLINK Bridge AV Interface 3
OneLINK Bridge for HDBaseT Cameras 3
OneLINK Bridge For HDBaseT Cameras Used with Codecs 3
OneLINK Bridge For HDMI Cameras 4
OneLINK Bridge For HDMI Cameras Used with Codecs 5
A Quick Look at the OneLINK Device 7
Front Panel of the Receiver 7
Connector Panel of the Receiver 8
Connector Panel of the EZCamera Interface Module (EZIM) 9
Installing the OneLINK Device 10
Don’t Void Your Warranty! 10
Cabling Notes 10
Mounting the OneLINK Device 11
RS-232 Connector Pin-Outs 11
Visual Conventions for Connection Diagrams 11
Connections for HDBaseT Cameras 12
Kits and Systems for HDBaseT Cameras 12
Connecting a Vaddio HDBaseT Camera 13
Connections for HDBaseT Cameras Used with Codecs 14
Kits for HDBaseT Cameras Used with Codecs 14
Connecting a Vaddio HDBaseT Camera and Polycom Codec 15
Connecting a Vaddio HDBaseT Camera and Cisco Codec 17
Connections for HDMI Cameras 22
Kits for HDMI Cameras 22
Connecting a RoboSHOT HDMI Camera 23
Connecting a Polycom EagleEye IV Camera 24
Connecting a Cisco Camera 25
Connecting a Sony or Panasonic HDMI Camera 27
Connections for HDMI Cameras Used with Codecs 29
Kits for HDMI Cameras Used with Codecs 29
Connecting a RoboSHOT HDMI Camera and Polycom Codec 30
Connecting a Polycom EagleEye IV Camera and Polycom Codec 32
Connecting a RoboSHOT HDMI Camera and Cisco Codec 34
Connecting a Cisco Camera and Codec 39
Powering Up the Equipment 46
Configuration and Administration Tasks 46
Compatible Web Browsers 46
Accessing the Web Interface 47
Web Interface Cheat Sheet 48
Configuring Network Settings 49
Assigning a Hostname 50
Specifying Time Zone and NTP Server 50
Managing Access and Passwords 51
Adding Room Information to the Web Interface 51
Configuring Streaming Settings 52
Enabling Phantom Power to Microphones 53
Configuring Audio Settings 54
Muting the Microphones 54
Controlling Volume on Individual Inputs or Outputs 54
Default Microphone Settings 55
Microphone Settings for Environments with Audiences 56
Microphone Adjustments 57
Speaker Adjustments 58
Preventing Audio Feedback 59
Default Audio Matrix 60
Routing Audio 60
Viewing System Information 61
Saving (Exporting) or Restoring (Importing) a Configuration 61
Rebooting the OneLINK Device 62
Restoring Factory Settings 62
Starting a Firmware Update 63
Contacting Vaddio Technical Support and Viewing Diagnostics 64
Telnet Serial Command API 65
link power 65
audio volume 66
audio mute 67
audio route 68
audio crosspoint-gain 69
sleep 70
network settings get 70
network ping 71
system reboot 71
system factory-reset 72
history 73
version 73
help 74
exit 74
Specifications 75
iii
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Troubleshooting 76
Operation, Storage, and Care 78
Compliance Statements and Declarations of Conformity 79
OneLINK Bridge AV Interface 79
FCC Part 15 Compliance 79
ICES-003 Compliance 79
European Compliance 80
OneLINK HDMI EZCamera Interface Module (EZIM) 81
FCC Part 15 Compliance 81
ICES-003 Compliance 81
European Compliance 82
Warranty Information 83
Index 84
iv
Integrator's Complete Guide to the OneLINK Bridge AV Interface
1
Overview
This guide covers the OneLINK™ Bridge AV Interface, which is available in the following kit configurations
for use with Vaddio or third-party cameras, with or without third-party codecs.
n999-9595-000/001/009, OneLINK Bridge AV interface
n999-9620-000/001/009, OneLINK Bridge AV interface for Polycom EagleEye IV cameras with Polycom
codecs
n999-9630-000/001/009, OneLINK Bridge AV interfacefor Sony and Panasonic cameras
n999-9560-000/001/009, OneLINK Bridge AV interface for RoboSHOT HDMI cameras with Polycom
codecs
n999-9645-000/001/009, OneLINK Bridge AV interface for Vaddio HDBaseT cameras with Polycom
codecs
n999-9660-000/001/009, OneLINK Bridge AV interface for Cisco cameras with Cisco codecs
n999-9670-000/001/009, OneLINK Bridge AV interface for RoboSHOT HDMI cameras with Cisco
codecs
n999-9675-000/001/009, OneLINK Bridge AV interface for Vaddio HDBaseT cameras with Cisco codecs
n999-9690-000/001, OneLINK Bridge AV interface for RoboSHOT HDMI cameras
The OneLINK Bridge AV interfaceis also available as a component of several Vaddio camera systems.
Part number suffixes indicate power cord set types. Those ending in -000 include cord sets for use in North
America; -001 kits include cord sets for use in Europe and the UK; -009 kits include cord sets for use in
Australia and New Zealand.
If the camera extension is sold for use with an HDMI camera, it is shipped with a OneLINK EZCamera
Interface Module (EZIM).
What's in this Guide
This guide provides information about:
nUnpacking
nPhysical features
nInstallation
nConfiguration and system administration
nTelnet API for third-party control
nSpecifications
nTroubleshooting and maintenance
nWarranty
For your convenience, most of this information is also available in smaller, limited-purpose manuals:
nInstallation Guide for the OneLINK Bridge AV Interface – Unpacking, physical features,
installation, and initial power-on.
nConfiguration and Administration Guide for the OneLINK Bridge AV Interface – Physical
features, web interface for device configuration and system administration, and troubleshooting.
Download manuals, dimensional drawings, and other information from support.vaddio.com.
Features
nConverts any conference room to a BYOD environment, delivering a USB stream for soft-conferencing
clients
nIncorporates Vaddio’s market-leading AV Bridge functionality, connecting professional AV equipment to
PC applications via USB 3.0 media stream
nVideo with audio: Simultaneous uncompressed USB 3.0, HDMI 1.4b, and 3Gb/s HD-SDI; passes IP
stream if available from source
nTwo balanced audio inputs, line level or mic level; two balanced audio outputs, line level
nControl via web interface or Telnet; passes web-based, Telnet, and RS-232 serial control to connected
devices
nSimple, clutter-free camera installation – power, control, video, and streaming over one Cat-5e or better
cable
nExtends installation distance for HDMI and HDBaseT™ cameras up to 100 m (328 ft.)
nCompatible with Vaddio HDBaseT cameras – no EZCamera Interface Module (EZIM) needed
nCompatible with Vaddio and other HDMI cameras
nAvailable in system configurations with Vaddio cameras
nKits available for use with Polycom and Cisco codecs and other HDMI cameras
2
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Unpacking the OneLINK Bridge AV Interface
Make sure you received all the items you expected. Here are the packing lists for the OneLINK Bridge kits.
Every OneLINK device ships with a power supply and at least one AC cord set. The last three digits of the
kit part number contain the regional code that specifies which cord set(s). For most OneLINK kits, the part
numbers follow this convention:
nKits with part numbers ending in -000 include one AC cord set for North America.
nKits with part numbers ending in -001 include two AC cord sets, one for Europe and one for the UK.
nKits with part numbers ending in -009 include one AC cord set for Australia and New Zealand.
OneLINK Bridge for HDBaseT Cameras
OneLINK Bridge AV Interface for Vaddio HDBaseT Cameras, 999-9595-000/001/009
Camera not included.
nOneLINK Bridge AV interface
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm, qty. 4
nEZCamera RS-232 control adapter (998-1001-232)
nQuick-Start Guide 411-0009-01
OneLINK Bridge For HDBaseT Cameras
Used with Codecs
OneLINK Bridge for Vaddio HDBaseT Cameras with Polycom Codecs, 999-9645-000/001/009
Camera and codec not included.
nOneLINK Bridge AV interface
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm (qty. 4)
nFan-out cable, codec side, 2 ft. (0.6 m)
nEZCamera RS-232 control adapter 998-1001-232
nQuick-Start Guide 411-0009-01
3
Integrator's Complete Guide to the OneLINK Bridge AV Interface
OneLINK Bridge for Vaddio HDBaseT Cameras with Cisco Codecs, 999-9675-000/001/009
Camera and codec not included.
Note
If connecting to a Cisco SX20 codec, you will need to provide
a Cisco split cable, Cisco part number CAB-PHD4XS2-
SPLIT.
nOneLINK Bridge AV interface
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm (qty. 4)
nHDMI cable, 3 ft. (0.9 m)
nCustom-pinout Cat-5e cable for Cisco, 3 ft. (0.9 m)
nCat-5e patch cable, 3 ft. (0.9 m)
nEZCamera RS-232 control adapter 998-1002-232
nQuick-Start Guide 411-0009-01
OneLINK Bridge For HDMI Cameras
OneLINK Bridge for RoboSHOT HDMI Cameras, 999-9690-000/001/009
Camera not included.
nOneLINK Bridge AV interface
nOneLINK EZCamera Interface Module (EZIM) with
mounting screws
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm, qty. 4
nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)
nHDMI cable, 1 ft. (0.3 m)
nCat-5e patch cable, 1 ft. (0.3 m), qty. 2
nEZCamera RS-232 control adapter
nQuick-Start Guide 411-0009-02
OneLINK Bridge for Sony and Panasonic Cameras, 999-9630-000/001/009
Camera not included.
nOneLINK Bridge AV interface
nOneLINK EZCamera Interface Module (EZIM)
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm, qty. 4
nWall mount with mounting hardware for Sony and
Panasonic cameras
nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)
nPower cable EIAJ-04 to 3x6.3mm, 1 ft. (0.3 m)
nHDMI cable, 1 ft. (0.3 m)
nRJ-45 to 8-pin mini-DIN cable, 1 ft. (0.3 m)
nCat-5e patch cable, 1 ft. (0.3 m)
nQuick-Start Guide 411-0009-02
4
Integrator's Complete Guide to the OneLINK Bridge AV Interface
OneLINK Bridge For HDMI Cameras Used with Codecs
OneLINK Bridge for Polycom Cameras with Polycom Codecs, 999-9620-000/001/009
Camera and codec not included.
nOneLINK Bridge AV Interface
nOneLINK EZCamera Interface Module (EZIM)
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nWall mount with mounting hardware for Polycom codec
and camera
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm, qty. 4
nFan-out cable, EZIM side, 1 ft. (0.3 m)
nFan-out cable, codec side, 2 ft. (0.6 m)
nEZCamera RS-232 control adapter 998-1001-232
nQuick-Start Guide 411-0009-02
OneLINK Bridge for RoboSHOT HDMI with Polycom Codecs, 999-9640-000/001/009
Camera and codec not included.
nOneLINK Bridge AV interface
nOneLINK EZCamera Interface Module (EZIM)
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm, qty. 4
nFan-out cable, codec side, 2 ft. (0.6 m)
nCat-5e patch cable, 1 ft. (0.3 m), qty. 2
nHDMI cable, 1 ft. (0.3 m)
nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)
nQuick-Start Guide 411-0009-02
5
Integrator's Complete Guide to the OneLINK Bridge AV Interface
OneLINK Bridge for Cisco Cameras with Cisco Codecs, 999-9660-000/001/009
Camera and codec not included.
Note
If connecting to a Cisco SX20 codec, you will need to provide
a Cisco split cable, Cisco part number CAB-PHD4XS2-
SPLIT. This cable is also required when connecting to a Cisco
Precision 40 or Precision HD 1080p2.5x camera; you will need
two of them if connecting one of these cameras and an SX20
codec.
nOneLINK Bridge AV Interface
nOneLINK EZCamera Interface Module (EZIM) with
mounting screws
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nWall mount with mounting hardware for Cisco codec and
camera
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm, qty. 4
nPower cable EIAJ-04 to 5.5x2.1 mm, 1 ft. (0.3 m)
nHDMI cable, 1 ft. (0.3 m)
nHDMI cable, 3 ft. (0.9 m)
nCustom-pinout Cat-5e cable for Cisco cameras, 1 ft. (0.3 m)
nCustom-pinout Cat-5e cable for Cisco SX20, 3 ft. (0.9 m)
nCat-5e patch cable, 1 ft. (0.3 m)
nCat-5e patch cable, 3 ft. (0.9 m)
nEZCamera RS-232 control adapter 998-1002-232
nQuick-Start Guide 411-0009-02
OneLINK Bridge for RoboSHOT HDMI with Cisco Codecs, 999-9670-000
Camera and codec not included.
Note
If connecting to a Cisco SX20 codec, you will need to provide
a Cisco split cable, Cisco part number CAB-PHD4XS2-
SPLIT.
nOneLINK Bridge AV Interface
nOneLINK EZCamera Interface Module (EZIM) with
mounting screws
nPower supply, 48 VDC/1.36 A, with AC cord set(s)
nUSB 3.0 A to B cable, 6 ft. (1.8 m)
n3-position Phoenix connector plug, 3.5 mm, qty. 4
nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)
nHDMI cable, 1 ft. (0.3 m)
nHDMI cable, 3 ft (0.9 m)
nCustom-pinout Cat-5e cable for Cisco, 3 ft. (0.9 m)
nCat-5e patch cable, 1 ft. (0.3 m), qty. 2
nCat-5e patch cable, 3 ft. (0.9 m)
nEZCamera RS-232 control adapter 998-1002-232
nQuick-Start Guide
6
Integrator's Complete Guide to the OneLINK Bridge AV Interface
A Quick Look at the OneLINK Device
This section covers the physical features of the OneLINK Bridge AV interface.
All OneLINK kits include a receiver, which is typically co-located with other equipment, up to 328 ft (100 m)
away from the camera. OneLINK kits for use with HDMI cameras also include an EZCamera Interface
Module (EZIM) HDBaseT converter, which is mounted adjacent to the camera.
Front Panel of the Receiver
nUSB indicator – Illuminates when a USB stream is present.
nNetwork indicator – Illuminates when connected to the IP network.
nSource indicator – Illuminates when a video input is detected.
nOneLINK indicator – Illuminates when the OneLINK Bridge detects a connection to an HDBaseT
device or to the OneLINK EZIM.
nDisplay IP and MAC Address button (illuminated blue) – Outputs the OneLINK Bridge IP and MAC
addresses as an overlay on the HDMI, HD-SDI, and USB video outputs.
nPower System Reset button (illuminated red) – reboots the OneLINK Bridge without affecting the
connected camera.
Note
The OneLINK device does not control the camera; it passes IP and RS-232 traffic to and from the camera.
Use the camera's IP address to access the camera's web interface. The OneLINK device's IP address
only provides access to the OneLINK device, not to the connected camera.
Note
To discover the attached Vaddio camera's IP address, point the IR Remote Commander at the camera and
press the Data Screen button. The camera's IP and MAC addresses are displayed on the connected HDMI
video output.
7
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connector Panel of the Receiver
From the left:
nPower input jack – Use the supplied 48VDC, 1.36A power supply.
nOneLINK interface port – Connect a Cat-5e (or better) cable to the EZIM, or to the camera if your
OneLINK kit or system did not include an EZIM. This bidirectional connection carries video, audio (if
available), network connectivity including H.264 IP streaming from the camera (if available), RS-232
control, and 12 VDC power.
nHDMI output – HDMI output to a connected display.
nUSB 3.0 – Uncompressed video output with PCM audio for conferencing applications
nHD-SDI – Video output from the camera
nNetwork port – H.264 IP streaming (if available from the camera), web interface access, and third-
party IP control via Telnet API.
nRS-232 port – Connect to a camera controller.
nAudio I/O Line Out 1 and Line Out 2 – Far-end audio from conferencing application or as configured
in the audio matrix
nAudio I/O Mic/Line In 1 and Mic/Line In 2 – Microphone or other audio inputs
8
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connector Panel of the EZCamera Interface Module (EZIM)
If the OneLINK device is used with an HDMI camera, the EZIM is required.
From the left:
nPower output jack – Supplies power to the camera. The kit you purchased includes the appropriate
cable to connect your camera's power input to this jack.
nNetwork port – Provides network connectivity to the camera for H.264 IP streaming (if available from
the camera), web interface access, and third-party control via Telnet API. Connect to the camera's
network port.
nRS-232 port – Provides RS-232 connectivity to the camera, for third-party control. The kit you
purchased may include a cable and/or an RS-232 adapter to connect to the camera's RS-232 port.
nHDMI input – Receives HDMI video from the camera. Connect to the camera's HDMI output.
nOneLINK port – Single-cable connection to the OneLINK receiver. This bidirectional connection
carries all video, power, and control.
Note
Cat-6 or Cat-7 cabling may provide better performance in noisier RF or EMF environments. When in doubt,
use shielded Cat-6 cable. Cable distance between the EZIM and the OneLINK device is a maximum of 328
feet (100 m).
9
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Installing the OneLINK Device
This section covers:
nThings to know before you start the installation
nBasic connection examples
Rack mounting brackets are available for the OneLINK receiver.
Don’t Void Your Warranty!
Caution
Use only the power supply included with this product. Using a different one will void the warranty, and
could create unsafe operating conditions or damage the product.
Do not connect the OneLINK power supply to a camera. It does not provide the correct voltage for Vaddio
cameras, and will damage the camera and void the camera's warranty.
This product is for indoor use only. Do not install it outdoors or in a humid environment. Do not allow it to
come into contact with any liquid.
Do not install or operate this product if it has been dropped, damaged, or exposed to liquids. If any of these
things happen, return it to Vaddio for safety and functional testing.
All information about this product is available for download at www.vaddio.com/support – no cost, no
registration required.
Cabling Notes
Cat-6 or Cat-7 cabling may provide better performance in noisier RF or EMF environments. When in doubt,
use shielded Cat-6 cable. Cable distance between the EZIM and the OneLINK device is a maximum of 328
feet (100 m).
Note
Use standard RJ-45 connectors and a good crimping tool. Do not use pass-through RJ-45
connectors. Poorly crimped connectors can damage the connectors on the product, cause
intermittent connections, and degrade signal quality. Test cable pin-outs and continuity
before connecting them.
Intact – Contact fingers will make reliable
contact with the cable connector
Damaged – Some contact fingers are bent
and will NOT make reliable contact with the
cable connector
Pro Tip
To prevent tragic mishaps, label both ends of every cable.
10
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Mounting the OneLINK Device
If you are installing the OneLINK device with a OneLINK EZIM, mount the EZIM with or near the camera.
Most Vaddio Thin Profile Wall Mounts include two mounting holes to attach the EZIM to the underside of
the mount using two 6-32 screws. Connect all required cables during camera installation.
Rack and under-table mounting kits are available for the receiver. Follow the mounting instructions supplied
with the kit.
RS-232 Connector Pin-Outs
OneLINK Receiver - RS-232 Control Port
1. Unused
2. Unused
3. Unused
4. Unused
5. Unused
6. GND – green
7. RX (from TX of controller) – brown/white
8. TX (to RX of controller) – brown
OneLINK EZIM - RS-232 Control Port
1. Unused
2. Unused
3. Unused
4. IR GND
5. IR (non-mod)
6. GND – green
7. TX (to RX of camera) – brown/white
8. RX (from TX of camera) – brown
Note
Vaddio recommends adhering to the 568B cabling standard for Cat-5 cabling.
Visual Conventions for Connection Diagrams
The following sections provide representative connection diagrams for the various OneLINK kit and system
configurations available. All diagrams in this guide use these visual conventions for connection type.
11
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connections for HDBaseT Cameras
In this configuration, the OneLINK Bridge extends network connectivity, power, and control to an
HDBaseT camera, and brings HDMI video from the camera to a display. The camera can optionally be
controlled by a camera controller on an RS-232 serial connection to the OneLINK Bridge or over the
network, depending on the controller. The OneLINK Bridge also provides connections for microphones and
speakers, and can originate a USB stream to bridge the non-USB camera and audio equipment into a USB-
based conferencing application.
If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming
resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including
resolution) are configured on the camera, not the OneLINK device.
Kits and Systems for HDBaseT Cameras
This block diagram applies to:
nOneLINK Bridge for Vaddio HDBT Cameras, 999-9595-000/001/009 – compatible with all Vaddio
HDBaseT cameras.
nRoboSHOT 12 HDBT OneLINK Bridge System, 999-9960-200/201/209
nRoboSHOT 30 HDBT OneLINK Bridge System, 999-9963-200/200W/201/201W/209/209W
nRoboSHOT 20 UHD OneLINK Bridge System, 999-9950-200/200W/201/201W/209/209W
nDocCAM 20 HDBT OneLINK Bridge System, 999-9968-300/301/309
nFuture systems consisting of a Vaddio HDBaseT camera and a OneLINK Bridge AV interface
12
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Vaddio HDBaseT Camera
999-9595-000/001/009
In this diagram, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT 12
HDBT camera, and brings HDMI video from the camera to a display. The OneLINK Bridge also provides
audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based
conferencing application.
Items in this diagram:
nOneLINK BridgeAV interface
nRoboSHOT 12 HDBT camera (not included in kit 999-9595-000/001/009)
nHDMI display and HDMI cable (not included)
nLaptop using soft conferencing client (not included)
nUSB 3.0 cable to laptop
nAudio cables (not included) terminated with supplied connectors
nConnections to microphones and speakers (not included)
nCat-5e cables for OneLINK and network connections (not included)
RoboSHOT HDBT Camera
Other Vaddio HDBaseT cameras connect in the same way.
Camera Configuration
You can configure the following settings on your Vaddio HDBaseT camera:
nHDMI output resolution: Depending on the camera, set this using the rotary switch on the back of the
camera or the virtual rotary switch on DIP Switches tab of the System page.
nIP streaming: Streaming page. Settings include Enable/disable, streaming quality, and streaming
resolution.
Point the remote at the camera and press the Data Screen button to see the camera's IP address on the
connected display.
No additional configuration is required.
13
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connections for HDBaseT Cameras Used with Codecs
In this configuration, the OneLINK HDMI extends network connectivity, power, and control to an HDBaseT
camera, and brings HDMI video from the camera to a connected codec. The codec may be connected to
the OneLINK device directly via RS-232, or they may communicate over the IP network, depending on the
codec. The OneLINK Bridge can originate a USB stream to bridge the camera, codec, and codec-
connected audio equipment into a USB-based conferencing application.
If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming
resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including
resolution) are configured on the camera, not the OneLINK device.
Kits for HDBaseT Cameras Used with Codecs
This block diagram applies to:
nOneLINK Bridge for Vaddio HDBT Cameras with Polycom Codecs, 999-9645-000/001/009 –
compatible with all Vaddio HDBT cameras and with Polycom RealPresence Group Series codecs.
nOneLINK Bridge for Vaddio HDBT Cameras with Cisco Codecs, 999-9675-000/001/009 – compatible
with all Vaddio HDBT cameras and with Cisco C20, C40, C60, SX20, and SX80 codecs.
14
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Vaddio HDBaseT Camera and Polycom Codec
999-9645-000/001/009
In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT
12 HDBT camera, and connects the camera to a Polycom codec. The OneLINK Bridge also provides audio
connections, and can originate a USB stream to bridge non-USB equipment into a USB-based
conferencing application.
Other Vaddio HDBaseT cameras would be connected in exactly the same way.
Items in these diagrams:
nOneLINK Bridge AV interface
nPower supply with AC cord set
nCodec-side fan-out cable
nRoboSHOT 12 HDBT camera (not included)
nPolycom RealPresence Group Series codec (not included)
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
RoboSHOT HDBT Camera and Polycom RealPresence Group 310 Codec
The Group 500 codec looks very similar and connects in the same way.
Other Vaddio HDBaseT cameras connect in the same way.
15
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDBT Camera and Polycom RealPresence Group 700 Codec
Other Vaddio HDBaseT cameras connect in the same way.
Hardware Note: IR Forwarding
Although the OneLINK Bridge does not support IR forwarding, the two unterminated wires of the fan-out
cable can be terminated and connected to an IR emitter (repeater).
Hardware Note: Connection and Configuration Changes
After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that
rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.
Camera Configuration
Point the remote at the camera and press the Data Screen button to see the camera's IP address on the
connected display.
You can configure the following settings on your Vaddio HDBaseT camera:
nHDMI output resolution: Depending on the camera, set this using the rotary switch on the back of the
camera or the virtual rotary switch on DIP Switches tab of the System page.
nIP streaming: Streaming page. Settings include Enable/disable, streaming quality, and streaming
resolution.
nCodec Control Mode: Soft DIP on the DIP Switches tab of the System page.
nIR: ON (default). DIP switch 3 on the back of RoboSHOT 20 UHD or RoboSHOT HDBT cameras, soft
DIP 3 on the DIP Switches tab of the System page for DocCAM 20 HDBT.
Note
Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware
update to add this capability.
16
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Vaddio HDBaseT Camera and Cisco Codec
999-9675-000/001/009
In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT
12 HDBT camera, and connects the camera to a Cisco codec. The OneLINK Bridge also provides audio
connections, and can originate a USB stream to bridge non-USB equipment into a USB-based
conferencing application.
Other Vaddio HDBaseT cameras would be connected in exactly the same way.
Items in these diagrams:
nOneLINK Bridge AV interface
nPower supply and AC cord set
nRS-232 adapter 998-1002-232 (used with standard Cat-5 cable on C20, C60. and SX80 codecs)
nCisco split cable CAB-PHD4XS2-SPLIT(not included; required for SX20 codec)
nCodec-side null modem cable (used with split cable on SX20 codec)
nRoboSHOT 12 HDBT camera (not included)
nCisco codec (not included)
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
RoboSHOT HDBT Camera and Cisco C20 Codec
Other Vaddio HDBaseT cameras connect in the same way.
17
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDBT Camera and Cisco C60 Codec
The C40 codec looks very similar and connects in the same way.
Other Vaddio HDBaseT cameras connect in the same way.
18
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDBT Camera and Cisco SX20 Codec
Other Vaddio HDBaseT cameras connect in the same way.
Note
If connecting to a Cisco SX20 codec, you will need to provide a Cisco split cable, Cisco part number CAB-
PHD4XS2-SPLIT.
19
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDBT Camera and Cisco SX80 Codec
Other Vaddio HDBaseT cameras connect in the same way.
Hardware Note: RS-232 Connections
For RS-232 connections to Cisco gear using DE-9 connectors, use the 998-1002-232 RJ-45 to DE-9
adapter. Its wiring differs from the 998-1001-232 adapter shipped with many Vaddio products.
For RS-232 connections to Cisco gear using the Cisco split cable, use the appropriate null-modem cable to
the RJ-45 side of the split cable. Connect the null-modem cable as indicated on the cable labels.
Hardware Note: Connection and Configuration Changes
After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that
rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.
20
Integrator's Complete Guide to the OneLINK Bridge AV Interface
OneLINK Device Configuration
After installation is complete and the OneLINK device and camera are operational, you will need to change
the AEC reference if you made the audio connections as shown in these diagrams.
On the Audio page of the OneLINK Bridge web interface, set Master Output/AEC Reference to Output 2 if
using Line Out 2 for the speaker connection.
Camera Configuration
Point the remote at the camera and press the Data Screen button to see the camera's IP address on the
connected display.
You can configure the following settings on your Vaddio HDBaseT camera:
nHDMI output resolution: Depending on the camera, set this using the rotary switch on the back of the
camera or the virtual rotary switch on DIP Switches tab of the System page.
nIP streaming: Streaming page. Settings include Enable/disable, streaming quality, and streaming
resolution.
nCodec Control Mode: Soft DIP on the DIP Switches tab of the System page.
nIR: ON (default). DIP switch 3 on the back of RoboSHOT 20 UHD or RoboSHOT HDBT cameras, soft
DIP 3 on the DIP Switches tab of the System page for DocCAM 20 HDBT.
Note
Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware
update to add this capability.
21
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connections for HDMI Cameras
In this configuration, the OneLINK Bridge extends network connectivity, power, and control to an HDMI
camera, and brings HDMI video from the camera to a display. The camera can optionally be controlled by a
camera controller on an RS-232 serial connection to the OneLINK Bridge or over the network, depending on
the controller. The OneLINK Bridge also provides connections for microphones and speakers, and can
originate a USB stream to bridge the non-USB camera and audio equipment into a USB-based
conferencing application.
If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming
resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including
resolution) are configured on the camera, not the OneLINK device.
Kits for HDMI Cameras
This block diagram applies to:
nOneLINK Bridge AV interface for Polycom cameras with Polycom Codecs, 999-9620-000/001/009,
when used without a codec – compatible with Polycom EagleEye IV camera.
nOneLINK Bridge AV Interface for Sony and Panasonic Cameras, 999-9630-000/001/009 – compatible
with Panasonic HE-series, Sony EVI-D series, and Sony BRC-H series cameras.
nOneLINK Bridge AV interface for Cisco Cameras with Cisco Codecs, 999-9660-000/001/009, when
used without a codec – compatible with Cisco Precision series cameras.
nOneLINK Bridge AV Interface for RoboSHOT HDMICameras, 999-9690-000/001/009
22
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a RoboSHOT HDMI Camera
999-9690-000/001/009
In this diagram, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT
HDMI camera, and brings camera video to the connected HDMI display. The OneLINK Bridge also
provides audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-
based conferencing application.
Items in this diagram:
nOneLINK Bridge AV interface and OneLINK EZIM
nOneLINK power supply and AC cord set
nRoboSHOT 12 HDMI camera (not included)
nPower cable, HDMI cable, and Cat-5e cables from the OneLINK EZIM to the camera
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
Camera Configuration
Set HDMI output resolution using the rotary switch on the back of the camera. No additional configuration
is required; if desired, additional configuration is available via the camera's web interface. Point the remote
at the camera and press the Data Screen button to see the camera's IP address on the connected HDMI
display.
23
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Polycom EagleEye IV Camera
999-9620-000/001/009
In this diagram, the OneLINK Bridge extends network connectivity, power, and control to a Polycom
EagleEye IV camera, and brings HDMI video from the camera to a display. The OneLINK Bridge also
provides audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-
based conferencing application.
Items in this diagram:
nOneLINK Bridge AV interface and OneLINK EZIM
nPower supply and AC cord set
nCamera-side fan-out cable
nPolycom EagleEye IV camera (not included)
nHDMI display and cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
24
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Cisco Camera
999-9660-000/001/009
In these diagrams, the OneLINK Bridge extends power and control to a Cisco camera, and brings HDMI
video from the camera to a display. The OneLINK Bridge also provides audio connections, and can
originate a USB stream to bridge non-USB equipment into a USB-based conferencing application.
nOneLINK BridgeAV interface and OneLINK EZIM
nCamera-side fan-out cable (not included; used with Precision 40 and Precision HD 1080p2.5x)
nCisco camera (not included)
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
Cisco Precision 40 or Precision HD Series Camera
Note
If connecting to a Cisco Precision 40 or Precision HD 1080p2.5x camera, you will need to provide a Cisco
split cable, Cisco part number CAB-PHD4XS2-SPLIT.
25
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Cisco Precision 60 Camera
Hardware Note: RS-232 Connections
For RS-232 connections to Cisco cameras, use the appropriate null-modem cable. Connect it as indicated
on the cable labels. This cable is used with the Cisco split cable CAB-PHD4XS2-SPLIT for some
cameras.
26
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Sony or Panasonic HDMI Camera
999-9630-000/001/009
In these diagrams, the OneLINK Bridge extends power and control to a Sony or Panasonic HDMI camera,
and brings video from the camera to a display. The OneLINK Bridge also provides audio connections, and
can originate a USB stream to bridge non-USB equipment into a USB-based conferencing application.
Items in this diagram:
nOneLINK Bridge AV interface and OneLINK EZIM
nPower supply and AC cord set
nCamera with cables (not included)
nHDMI display and cable (not included)
nLaptop with soft conferencing client (not included)
Panasonic AW-HE130 Camera
27
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Sony SRG300 Camera
The SRG120 camera's connector panel looks very similar, and connects in the same way.
28
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connections for HDMI Cameras Used with Codecs
In this configuration, the OneLINK HDMI extends network connectivity, power, and control to an HDMI
camera, and brings HDMI video from the camera to a connected codec. The codec may be connected to
the OneLINK device directly via RS-232, or they may communicate over the IP network, depending on the
codec. The OneLINK Bridge can originate a USB stream to bridge the camera, codec, and codec-
connected audio equipment into a USB-based conferencing application.
If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming
resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including
resolution) are configured on the camera, not the OneLINK device.
Kits for HDMI Cameras Used with Codecs
This block diagram applies to:
nOneLINK Bridge for Polycom Cameras with Polycom Codecs, 999-9620-000/001/009 – compatible
with Polycom EagleEye IV camera and Polycom RealPresence Group Series codecs.
nOneLINK Bridge for RoboSHOT HDMICameras with Polycom Codecs, 999-9640-000/001/009 –
compatible with RoboSHOT HDMI HDMI cameras and Polycom RealPresence Group Series codecs.
nOneLINK Bridge for Cisco Cameras with Cisco Codecs, 999-9660-000/001/009 – compatible with
Cisco Precision series cameras and Cisco C20, C40, C60, SX20, and SX80 codecs.
nOneLINK Bridge for RoboSHOT HDMI Cameras with Cisco Codecs, 999-9670-000/001/009 –
compatible with RoboSHOT HDMI cameras and with Cisco C20, C40, C60, SX20, and SX80 codecs.
29
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a RoboSHOT HDMI Camera and Polycom Codec
999-9640-000/001/009
In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT
12 or 30 HDMI camera, and connects the camera to a Polycom codec. The OneLINK Bridge also provides
audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based
conferencing application.
Items in these diagrams:
nOneLINK Bridge AV interface and OneLINK EZIM
nPower supply with AC cord set
nRoboSHOT 12 HDMI camera (not included)
nPolycom RealPresence Group Series codec (not included)
nCodec-side fan-out cable
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
RoboSHOT HDMI Camera and Polycom RealPresence Group 310 Codec
The Group 500 codec looks very similar and connects in the same way.
30
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDMI Camera and Polycom RealPresence Group 700 Codec
Hardware Note: IR Forwarding
Although the OneLINK Bridge does not support IR forwarding, the two unterminated wires of the fan-out
cable can be terminated and connected to an IR emitter (repeater).
Hardware Note: Connection and Configuration Changes
After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that
rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.
Camera Configuration
Set HDMI resolution and IR forwarding using the switches on the back of the camera:
nSet HDMI output resolution using the rotary switch.
nSet DIP switch 3 DOWN to enable IR forwarding.
Codec Control Mode and other configuration settings are available from the camera's web interface. Point
the remote at the camera and press the Data Screen button to see the camera's IP address on the
connected HDMI display.
Enable Codec Control Mode on the DIP Switches tab of the System page.
Note
Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware
update to add this capability.
31
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Polycom EagleEye IV Camera and Polycom Codec
999-9620-000/001/009
In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a Polycom
EagleEye IV camera, and connects the camera to a Polycom codec. The OneLINK Bridge also provides
audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based
conferencing application.
Items in these diagrams:
nOneLINK Bridge AV interface and OneLINK EZIM
nPower supply with AC cord set
nPolycom EagleEye IV camera (not included)
nPolycom RealPresence Group Series codec (not included)
nCodec-side fan-out cable
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
Polycom EagleEye IV Camera and Polycom RealPresence Group 310 Codec
The Group 500 codec looks very similar and connects in the same way.
32
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Polycom EagleEye IV Camera and Polycom RealPresence Group 700 Codec
Hardware Note: IR Forwarding
Although the OneLINK Bridge does not support IR forwarding, the two unterminated wires of the fan-out
cable can be terminated and connected to an IR emitter (repeater).
Hardware Note: Connection and Configuration Changes
After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that
rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.
33
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a RoboSHOT HDMI Camera and Cisco Codec
999-9670-000/001/009
In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT
12 or 30 HDMI camera, and connects the camera to a Cisco codec. The OneLINK Bridge also provides
audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based
conferencing application.
Items in these diagrams:
nOneLINK Bridge AV interface and OneLINK EZIM
nPower supply and AC cord set
nRS-232 adapter 998-1002-232 (used with standard Cat-5 cable on C20, C60. and SX80 codecs)
nCisco split cable CAB-PHD4XS2-SPLIT (not included; required for SX20 codec)
nCodec-side null modem cable (used with split cable on SX20 codec)
nRoboSHOT 12 HDMI camera (not included)
nCisco codec (not included)
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
RoboSHOT HDMI Camera and Cisco C20 Codec
34
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDMI Camera and Cisco C60 Codec
The C40 codec looks very similar and connects in the same way.
35
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDMI Camera and Cisco SX20 Codec
Note
If connecting to a Cisco SX20 codec, you will need to provide a Cisco split cable, Cisco part number CAB-
PHD4XS2-SPLIT.
36
Integrator's Complete Guide to the OneLINK Bridge AV Interface
RoboSHOT HDMI Camera and Cisco SX80 Codec
Hardware Note: RS-232 Connections
For RS-232 connections to Cisco gear using DE-9 connectors, use the 998-1002-232 RJ-45 to DE-9
adapter. Its wiring differs from the 998-1001-232 adapter shipped with many Vaddio products.
For RS-232 connections to Cisco gear using the Cisco split cable, use the appropriate null-modem cable to
the RJ-45 side of the split cable. Connect the null-modem cable as indicated on the cable labels.
Hardware Note: Connection and Configuration Changes
After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that
rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.
37
Integrator's Complete Guide to the OneLINK Bridge AV Interface
OneLINK Device Configuration
After installation is complete and the OneLINK device and camera are operational, you will need to change
the AEC reference if you made the audio connections as shown in these diagrams.
On the Audio page of the OneLINK Bridge web interface, set Master Output/AEC Reference to Output 2 if
using Line Out 2 for the speaker connection.
Camera Configuration
Set HDMI resolution and IR forwarding using the switches on the back of the camera:
nSet HDMI output resolution using the rotary switch.
nSet DIP switch 3 DOWN to enable IR forwarding.
Codec Control Mode and other configuration settings are available from the camera's web interface. Point
the remote at the camera and press the Data Screen button to see the camera's IP address on the
connected HDMI display.
Enable Codec Control Mode on the DIP Switches tab of the System page.
Note
Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware
update to add this capability.
38
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Connecting a Cisco Camera and Codec
999-9660-000/001/009
In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a Cisco
camera, and connects the camera to a Cisco codec. The OneLINK Bridge also provides audio
connections, and can originate a USB stream to bridge non-USB equipment into a USB-based
conferencing application.
Items in these diagrams:
nOneLINK BridgeAV interface and OneLINK EZIM
nCisco split cable CAB-PHD4XS2-SPLIT (not included; required for SX20 codec and for Precision 40
and Precision HD 1080p2.5x cameras)
nCamera-side null modem cable (used on all supported Cisco cameras)
nCodec-side null modem cable (used with Cisco split cable on SX20 codec)
nRS-232 adapter 998-1002-232 (used with standard Cat-5 cable on C20, C60. and SX80 codecs)
nCisco camera (not included)
nCisco codec (not included)
nHDMI display and HDMI cable (not included)
nLaptop with soft conferencing client (not included)
nCat-5e cables for OneLINK and network connections (not included)
Note
If connecting to a Cisco SX20 codec, you will need to provide a Cisco split cable, Cisco part number CAB-
PHD4XS2-SPLIT. This cable is also required when connecting to a Cisco Precision 40 or Precision HD
1080p2.5x camera; you will need two of them if connecting one of these cameras and an SX20 codec.
39
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Cisco Precision 40 or Precision HD Series Camera and Cisco C20 Codec
40
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Cisco Precision 40 or Precision HD Series Camera and Cisco C60 Codec
The C40 codec looks very similar and connects in the same way.
41
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Cisco Precision 40 or Precision HD Series Camera and Cisco SX20 Codec
42
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Cisco Precision 40 or Precision HD Series Camera and Cisco SX80 Codec
43
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Cisco Precision 60 Camera and Cisco SX80 Codec
Hardware Note: RS-232 Connections
For RS-232 connections to Cisco gear using DE-9 connectors, use the 998-1002-232 RJ-45 to DE-9
adapter. Its wiring differs from the 998-1001-232 adapter shipped with many Vaddio products.
For RS-232 connections to Cisco gear using the Cisco split cable, use the appropriate null-modem cable to
the RJ-45 side of the split cable. Connect the null-modem cable as indicated on the cable labels.
Hardware Note: Connection and Configuration Changes
After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that
rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.
44
Integrator's Complete Guide to the OneLINK Bridge AV Interface
OneLINK Device Configuration
After installation is complete and the OneLINK device and camera are operational, you will need to change
the AEC reference if you made the audio connections as shown in these diagrams.
On the Audio page of the OneLINK Bridge web interface, set Master Output/AEC Reference to Output 2 if
using Line Out 2 for the speaker connection.
45
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Powering Up the Equipment
Power up the connected equipment that is not powered by the OneLINK device (such as displays and third-
party control devices), then connect power to the OneLINK device. The connected camera and the
OneLINK device power up together.
Configuration and Administration Tasks
The OneLINK Bridge AV interface provides a web interface to allow configuration and administration using
a browser.
The web interface allows password-protected access to tasks such as setting passwords, changing the IP
address, viewing diagnostics, and installing firmware updates.
Note
The OneLINK device is not a camera control device. To configure or operate the camera, use the camera's
web interface. Refer to the camera's documentation for details.
Note
The connected camera is configured separately from the OneLINK device. Changes to the OneLINK
device's configuration do not affect the configuration of the camera or other connected equipment. If you
need to change the way the camera is configured, log in to the camera's web interface.
Compatible Web Browsers
We have tested this product with these web browsers:
nChrome®
nFirefox®
nMicrosoft® Internet Explorer®
nSafari®
We test using the browser version available from the vendor at that time. Older versions of these browsers
are likely to work, and other browsers may also work.
46
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Accessing the Web Interface
To get the IP address:
Press the button labeled Display IP and MAC Address, on the front of the unit. The information is overlaid
on the HDMI, HD-SDI, and USB video outputs.
The OneLINK device will use the default address of 169.254.10.1 if no DHCP server is available. In this
situation, you will need to connect a computer to the OneLINK device's network port and configure network
settings. Depending on the computer, you may need a crossover cable.
To access the web interface:
Enter the IP address or hostname in your browser's address bar. If you use the hostname, you may need to
enter http:// as a prefix to keep the browser from treating it as a search query.
The login page opens. The username admin and the default password is password.
After you log in, the System page opens.
Note
For best security, Vaddio strongly recommends changing the default password. Using default passwords
leaves the product vulnerable to tampering. See Managing Access and Passwords.
47
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Web Interface Cheat Sheet
You must log in to access the pages for all system administration tasks.
Note
The OneLINK device's web interface does not provide access to the connected camera. To configure the
camera, use the camera's web interface, which is at a separate IP address.
What do you need to do? Go to this page
Mute the connected microphone(s) Mute button on all pages
Adjust audio inputs and outputs Audio
Allow conferencing applications to control the audio Streaming
Enable or disable USB streaming Streaming
Find the current firmware version System
Change the Admin password Security
Reboot, restore factory defaults, or run firmware updates System
Add or change information about the room where the equipment is
installed, or the phone number for A/V support
Room Labels
Configure time zone or NTP settings Networking
Specify whether idle sessions close automatically Security
Configure IP addressing Networking
View or change the OneLINK device's hostname Networking
View or change the OneLINK device's USB device name Streaming
Access contact information for Vaddio technical support Help
View or download diagnostic logs for technical support Diagnostics
For your convenience, the navigation panel also provides an elegant Logout button for ending your session
gracefully – and leaving the web interface in a password-protected state.
48
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Configuring Network Settings
NETWORKING PAGE
These settings are for the OneLINK device only. The camera is configured separately.
DHCP addressing is the default setting. In a DHCP environment, you will not need to change the network
configuration.
The OneLINK device will use the default address of 169.254.10.1 if no DHCP server is available. In this
situation, you will need to connect a computer to the OneLINK device's network port and configure network
settings. Depending on the computer, you may need a crossover cable.
Caution
Consult your IT department before changing network settings. Errors in network configuration can make
the OneLINK device and connected equipment inaccessible from the network. Do not change
DHCP/Static addressing, IP address, subnet mask, or gateway unless you are very familiar with the
characteristics and configuration of the network where you install the equipment.
To assign a static IP address:
1. Select static IP addressing.
2. Specify the IP address, subnet mask, and gateway address.
3. Save your changes.
Pro Tip
Make sure you have a way to remember the IP address. There is no hardware factory reset.
49
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Assigning a Hostname
NETWORKING PAGE
The default hostname for the OneLINK BridgeAV interface is the string vaddio-onelink-bridge-
followed by the device's MAC address. You can change this in the Hostname field.
If your network supports hostname resolution, you can browse to the OneLINK device by hostname even if
you cannot readily determine its IP address. In this situation, you may wish to assign a hostname
according to your IT department's naming guidelines.
To edit the hostname:
Enter the desired hostname in the Hostname text box, and save your changes.
Specifying Time Zone and NTP Server
NETWORKING PAGE
To ensure that data exports receive accurate time stamps, and to display the correct date and time on the
Networking page, NTP updating must be enabled.
1. Enable Automatic NTP Updating.
2. Select the desired time zone from the list.
3. If desired, specify the NTP server to use. Otherwise, use the default.
4. Select Refresh to update the displayed date and time.
50
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Managing Access and Passwords
SECURITY PAGE
Things you can do on this screen:
nSet whether inactive sessions log off automatically or not
nChange the password for the admin account (default is password)
Note
For best security, Vaddio strongly recommends changing passwords from the default. Using default
passwords leaves the product vulnerable to tampering.
Pro Tip
Make sure you have a way to remember the admin password. There is no hardware factory reset.
Adding Room Information to the Web Interface
ROOM LABELS PAGE
On this page, you can provide information about the OneLINK Bridge AV interface's location:
nName of the organization
nName of the room where the equipment is installed
nPhone number of the room where the equipment is installed
nPhone number for the AV or IT support team
This information appears on every page of the OneLINK web interface.
Note
This does not affect the room information (if any) presented on the web interface for the attached camera.
51
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Configuring Streaming Settings
STREAMING PAGE
The camera's settings are used for IP streaming; the OneLINK BridgeAV interface passes the IP stream
from the camera and does not require additional IP streaming configuration.
For non-USB cameras, the OneLINK Bridge AV interface provides USB streaming capability. On the
Streaming page, you can:
nDisable/enable USB streaming
nAllow the conferencing application to control the audio
nEdit the USB device name
After making changes on this page, save them.
To disable or enable streaming:
USB streaming is enabled by default. Use the Enable USB Streaming checkbox to change this.
To control the audio from a computer:
Check the Enabled box for HID Audio Controls.
Note
When HID Audio Controls are enabled, we recommend controlling volume manually. Allowing the
conferencing application to manage the volume automatically can produce undesirable results.
To edit the USB device name:
To change the way the OneLINK device shows up in your soft client's selection list, edit the USB Device
Name.
52
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Enabling Phantom Power to Microphones
AUDIO PAGE, ANALOG TAB
To supply 48 VDC phantom power to a connected microphone, check the Phantom Power checkbox below
the controls for the Line/Mic input.
53
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Configuring Audio Settings
AUDIO PAGE
The web interface provides separate controls for each of the audio inputs and outputs:
nAnalog (Mic/Line In 1 and 2, and Line Out 1 and 2)
nDigital (HDBT Input left and right, HDMI Output left and right, SDI Output left and right)
nStreaming (USB Playback left and right, HDBT Output left and right, USB Record left and right)
The Matrix tab of the Audio page defines audio routing.
Muting the Microphones
Use the Mute control at the top of any page.
Controlling Volume on Individual Inputs or Outputs
AUDIO PAGE, ANALOG, DIGITAL, AND STREAMING TABS
Use the button to mute the desired audio input or output. Use the slider to set the volume.
Note
For best performance with most computers, we recommend setting the USB Record volume high.
54
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Default Microphone Settings
AUDIO PAGE, ANALOG TAB
Acoustic Echo Cancellation – Enabled; prevents audio feedback by cancelling the specified output
signal out of the line/mic input.
Note
If using the OneLINK Bridge with a conferencing codec, ensure that echo cancellation is enabled on only
one device, whether it is the OneLINK Bridge or the codec. If echo cancellation is enabled on both the
OneLINK Bridge and the codec, unexpected audio effects may result. We recommend disabling echo
cancellation on the OneLINK Bridge and allowing the conferencing codec to handle it.
Noise Cancellation – Enabled; suppresses ambient noise.
Automatic Gain Control – Disabled; adjusts gain to compensate for differences in volume as different
people speak.
55
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Microphone Settings for Environments with Audiences
AUDIO PAGE, ANALOG AND MATRIX TABS
Speech Lift: Feeds the signal from the specified microphone to the speakers in the room, so that people in
the back of the room can hear the person who is speaking.
Chairman Override: Gives priority to the specified microphone when more than one person is speaking.
(Matrix tab only)
56
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Microphone Adjustments
AUDIO PAGE, ANALOG TAB
To adjust for more natural speech reproduction:
nHigh-pass filter – Specify the lowest frequency that the microphone should pick up. Use this setting to
reduce low-frequency background noise such as heating/air conditioning systems.
nLow-pass filter – Specify the highest frequency that the microphone should pick up. Use this setting to
reduce hissing sounds and make speech sound natural.
nPEQ (parametric equalizer) – Increase or reduce the volume of specific frequency ranges to
compensate for the audio challenges unique to the situation.
Note
As a best practice, use the equalizer to attenuate undesirable frequency ranges rather than to boost the
desirable frequencies.
57
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Speaker Adjustments
AUDIO PAGE, ANALOG AND STREAMING TABS
To sync the sound with the video:
If the video lags noticeably behind the audio, check the Delay box for the appropriate audio outputs (Analog
or Streaming tab) and enter a delay value in msec. The delay may differ from one output to another.
To compensate for differing speech volumes:
If some people on the far end are inaudible while others are too loud, check the Compressor box to reduce
the dynamic range from the connected speakers. (Analog tab only.)
To compensate for specific audio issues on the far end:
Use the equalizers for the analog outputs to attenuate specific frequency ranges. This can help if the far-
end audio includes unwanted elements such as a rumbling HVAC system or a cricket in the room.
58
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Preventing Audio Feedback
AUDIO PAGE, ANALOG TAB
Audio feedback results when the microphones pick up audio from the speakers.
1. Select Echo Cancellation on any line inputs that are connected to signal sources.
2. In the Global Settings, under Master Output/AEC Reference, select the audio output to use as the
reference - the signal that will be cancelled out of the inputs.
59
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Default Audio Matrix
AUDIO PAGE, MATRIX TAB
The audio matrix shows where each audio output originates. Each column of the matrix shows one audio
output, and each row shows one audio input. Table cells highlighted in blue mean that the input represented
in that row is routed to the output represented in that column.
nUSB Playback left and right (far-end audio from the soft conferencing client) route to line output 1
(typically the speaker in your conference room).
nLine/Mic 1 (your room's microphone) routes to USB Record left and right (the audio that the
participants on the far end hear).
nHDBT left and right (far-end audio received as part of the HDMI signal over the HDBT connection)
routes to HDMI Output left and right, and goes to the HDMI display's speakers.
Routing Audio
AUDIO PAGE, MATRIX TAB
To specify how the OneLINK Bridge uses a given audio input, locate its row. Locate the column
representing the desired output and select the table cell where the desired row and column intersect.
Example: The USB stream has left and right audio channels, but by default Line/Mic 1 provides the source
for both channels of outbound USB audio (USB Record left and right) and both channels of incoming USB
audio are routed to Output 1 (Audio Line Out 1). You might choose to change the default matrix to provide
separate right and left channels of outbound and inbound USB audio.
60
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Viewing System Information
SYSTEM PAGE
The information on the System page includes the version – so you don't need to guess about whether the
latest update has already been installed.
The System page also provides controls to:
nReboot the OneLINK device
nBack up or restore configuration data
nRestore factory presets
nUpdate the firmware
Saving (Exporting) or Restoring (Importing) a Configuration
SYSTEM PAGE
You can save a known good configuration by exporting it. This allows you to quickly configure several
OneLINK devices the same way, by importing the configuration to all of them. It also gives you a quick way
to go back to a known good configuration if you are concerned about planned changes on a specific unit.
The configuration file can only be imported to a OneLINK device using the same version of firmware from
which the file was exported. You cannot export a configuration, update the firmware, and import the
configuration – but you won't need to. Firmware updates do not change the device configuration.
61
Integrator's Complete Guide to the OneLINK Bridge AV Interface
To export the current configuration:
Select Export Data. The configuration file downloads to your computer's default download location as a
.dat file. The filename is the device's hostname.
Note
You can import a configuration file from another OneLINK device; however, the configuration file can only
be imported to a device that is using the same version of firmware from which the file was exported. The
OneLINK device cannot import a configuration file that was exported from a different version of firmware.
To import a configuration file:
1. Select Import Data. The Import Data dialog opens.
2. Select Choose File, and select the configuration file. The filename is the OneLINK device's hostname,
with the file extension .dat. The OneLINK device loads the configuration and reboots.
Rebooting the OneLINK Device
SYSTEM PAGE
This may help if the OneLINK device stops responding as you expect.
In the System Utilities section of the System page, select Reboot.
Restoring Factory Settings
SYSTEM PAGE
Select Restore Factory Settings to return to the default configuration. Read the confirmation message
before you select Continue or Cancel.
62
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Starting a Firmware Update
SYSTEM PAGE
Caution
Do not remove power or disconnect the OneLINK device while a firmware update in progress. Interrupting a
firmware update can make the OneLINK device unusable.
1. Be sure you have downloaded the appropriate update file to your computer.
2. Select Choose File, browse to the firmware update file that you downloaded, and select it. The filename
ends with .p7m. The System page then displays the filename beside the Choose File button.
3. OPTIONAL: Select Export Data to save a copy of the OneLINK device's current configuration. You
probably won't need it, but it could save time if you need to roll back the update.
4. Select Begin Firmware Update.
5. READ the information in the Confirm dialog box and be sure you understand it. It's boring, but it could
save you a lot of time and aggravation.
6. When you are ready to start the update, select Continue.
7. If the update process presents warnings or error messages, read them carefully.
8. Contact Vaddio technical support if you encounter any problems with the update.
63
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Contacting Vaddio Technical Support and Viewing Diagnostics
HELP PAGE, DIAGNOSTICS PAGE
If you encounter an issue that you can't resolve using your superior troubleshooting skills (and perhaps the
Troubleshooting section of this guide), go to the Help page. This page provides Vaddio Technical Support
contact information.
Your Vaddio technical support representative may ask you to download and email the log file available from
the Diagnostics page.
The information on this page does not necessarily indicate errors or problems. Most of it is a log of code
execution that can be helpful later if technical support or engineering staff need to research an issue.
64
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Telnet Serial Command API
The Vaddio Telnet serial command API is a high-level, text-based command line interface to allow an
external device such as AMX or Crestron to control the OneLINK device. Use a Telnet client to access the
API via the network. The default Telnet port is 23. Telnet sessions require the admin account login.
Using a question mark as a command parameter will bring up
a list of available commands for the menu you are in.
Things to know about control via Telnet session:
nCommand lines are terminated with a carriage return.
nAll ASCII characters (including carriage returns) are
echoed to the terminal program and appended with the
VT100 string ESC[J (hex 1B 5B 4A), which most terminal
programs automatically strip.
nCTRL-5 Clears the current serial buffer on the device.
Typographical conventions:
n{ x | y | z} – Choose x, y, or z.
n<variable> – Substitute the desired value here.
n< x - y > – Valid range of values is from x through y.
n[parameter] – Parameter is not required.
Note
The commands in this guide refer to the OneLINK device. To control the camera itself, open a Telnet
session to the camera's IP address and use the camera's Telnet commands.
link power
Sets the camera connection on or off.
Note
The OneLINK device does not provide camera control. To set the camera to standby instead of powering it
off, use the camera's remote or other camera control interface to issue a standby command directly to the
camera.
Synopsis link power { on | off }
Options
off Powers off the camera connection.
on Powers on the camera connection.
Examples >link power off
OK
>
Powers off the camera connection.
65
Integrator's Complete Guide to the OneLINK Bridge AV Interface
audio volume
Gets or sets the volume of the specified audio channel.
Synopsis audio [channel] volume {get | on | off | toggle}
Channels
master Applies the command to all audio channels.
line_in_1
line_in_2
Line/Mic In ports (typically microphone inputs).
usb3_playback_left
usb3_playback_right
Audio portion of the incoming (far-end) USB
stream, left and right channels.
hdbt_in_left
hdbt_in_right
Audio portion of the incoming (far-end) HDMI
signal, left and right channels.
line_out_1
line_out_2
Line Out ports (typically speaker outputs).
usb3_record_left
usb3_record_right
Outbound (near-end) audio portion of the USB
stream, left and right channels.
hdmi_out_left
hdmi_out_right
Audio portion of the HDMI output (far-end audio to
the display's speakers), left and right channels.
sdi_out_left
sdi_out_right
Audio portion of the SDI output (far-end audio to
the display's speakers), left and right channels.
hdbt_out_left
hdbt_out_right
Outbound (far-end) audio portion of the IP stream,
left and right channels.
Options get Returns the current volume of the specified
channel.
up Increases the volume of the specified channel.
down Reduces the volume of the specified channel.
set Sets the volume of the specified channel.
Examples audio line_in_1 volume set -5
OK
>
Sets -5 dB as the volume for the device connected to the Line In 1 port.
audio line_out_1 volume get
volume -10.0 dB
OK
>
Returns the current volume for the speaker connected to the line out port.
66
Integrator's Complete Guide to the OneLINK Bridge AV Interface
audio mute
Gets or sets the mute status of the specified audio channel.
Synopsis audio [channel] mute {get | on | off | toggle}
Channels
master Applies the command to all audio channels.
line_in_1
line_in_2
Line/Mic In ports (typically microphone inputs).
usb3_playback_left
usb3_playback_right
Audio portion of the incoming (far-end) USB stream,
left and right channels.
hdbt_in_left
hdbt_in_right
Audio portion of the incoming (far-end) HDMI signal,
left and right channels.
line_out_1
line_out_2
Line Out ports (typically speaker outputs).
usb3_record_left
usb3_record_right
Outbound (near-end) audio portion of the USB
stream, left and right channels.
hdmi_out_left
hdmi_out_right
Audio portion of the HDMI output (far-end audio to the
display's speakers), left and right channels.
sdi_out_left
sdi_out_right
Audio portion of the SDI output (far-end audio to the
display's speakers), left and right channels.
hdbt_out_left
hdbt_out_right
Outbound (far-end) audio portion of the IP stream, left
and right channels.
Options
get Returns the current mute status of the specified
channel.
on Mutes the audio for the specified channel.
off Unmutes the audio for the specified channel.
toggle Changes the mute state for the specified channel –
unmutes if it was muted, mutes if it was not.
Examples > audio line_out_1 mute get
mute: off
OK
>
Returns the current mute state of the device connected to audio line out 1. Mute is off,
so the audio is on.
>audio master mute on
OK
>
Mutes all audio.
67
Integrator's Complete Guide to the OneLINK Bridge AV Interface
audio route
Gets or sets the input routed to the specified output.
Synopsis audio [channel] route {get | set}
Outputs
line_out_1
line_out_2
Line Out ports (typically speaker outputs).
usb3_record_left
usb3_record_right
Outbound (near-end) audio portion of the USB
stream, left and right channels.
hdmi_out_left
hdmi_out_right
Audio portion of the HDMI output (far-end audio to
the display's speakers), left and right channels.
sdi_out_left
sdi_out_right
Audio portion of the SDI output (far-end audio to
the display's speakers), left and right channels.
hdbt_out_left
hdbt_out_right
Outbound (far-end) audio portion of the IP stream,
left and right channels.
Options
get Returns the routing for the specified output.
set Sets the routing for the specified input.
Inputs
line_in_1
line_in_2
Line/Mic In ports (typically microphone inputs).
usb3_playback_left
usb3_playback_right
Audio portion of the incoming (far-end) USB
stream, left and right channels.
hdbt_in_left
hdbt_in_right
Audio portion of the incoming (far-end) HDMI
signal, left and right channels.
Examples > audio line_out_1 route get
[usb3_playback_left usb3_playback_right ]
OK
>
Returns the current source of the audio output on Line Out 1 (typically a speaker).
Both channels of far-end audio from the USB stream are currently routed to this
output.
68
Integrator's Complete Guide to the OneLINK Bridge AV Interface
audio crosspoint-gain
Returns or sets the current routing gain, in dB, for the crosspoint between a given output and input.
Synopsis audio <output> crosspoint-gain <input> {get | set <level>}
Outputs
line_out_1
line_out_2
Line Out ports (typically speaker outputs).
usb3_record_left
usb3_record_right
Outbound (near-end) audio portion of the USB
stream, left and right channels.
hdmi_out_left
hdmi_out_right
Audio portion of the HDMI output (far-end audio to
the display's speakers), left and right channels.
sdi_out_left
sdi_out_right
Audio portion of the SDI output (far-end audio to
the display's speakers), left and right channels.
hdbt_out_left
hdbt_out_right
Outbound (far-end) audio portion of the IP stream,
left and right channels.
Inputs
line_in_1
line_in_2
Line/Mic In ports (typically microphone inputs).
usb3_playback_left
usb3_playback_right
Audio portion of the incoming (far-end) USB
stream, left and right channels.
hdbt_in_left
hdbt_in_right
Audio portion of the incoming (far-end) HDMI
signal, left and right channels.
Options
get Returns the gain from the specified input to the
specified output.
set <-12.0 .. 12.0> Sets the gain from the specified input to the
specified output. Valid range is -12.0 dB to 12.0
dB.
Examples > audio program_out_left crosspoint-gain usb3_in_left get
3.9
OK
>
Returns the gain from the left channel of the USB 3 playback to the left channel of the
program output.
> audio program_out_left crosspoint-gain usb3_in_left set -3
OK
>
Sets the gain from the left channel of the USB 3 playback to the left channel of the
program output to -3 dB.
69
Integrator's Complete Guide to the OneLINK Bridge AV Interface
sleep
Pauses for the specified number of milliseconds before evaluating and executing the next command.
Synopsis sleep <milliseconds>
Options <milliseconds> The number of milliseconds (1 to 10000) to
pause.
Example >sleep 7000
OK
>
Pause for 7 seconds (7000 milliseconds) before returning.
network settings get
Returns the current network settings for MAC address, IP address, subnet mask, and gateway.
Synopsis network settings get
Example > network settings get
Name eth0:WAN
MAC Address 00:1E:C0:F6:CA:7B
IP Address 192.168.1.67
Netmask 255.255.255.0
VLAN Disabled
Gateway 192.168.1.254
OK
>
70
Integrator's Complete Guide to the OneLINK Bridge AV Interface
network ping
Sends an ICMP ECHO_REQUEST to the specified IP address or hostname.
Synopsis network ping [count <count>] [size <size>] <destination-ip>
Options <count> The number of ECHO_REQUEST packets to
send. Default is five packets.
<size> The size of each ECHO_REQUEST packet.
Default is 56 bytes.
<destination-ip> The IP address where the ECHO_REQUEST
packets will be sent.
Examples >network ping 192.168.1.66
PING 192.168.1.66 (192.168.1.66): 56 data bytes
64 bytes from 192.168.1.66: seq=0 ttl=64 time=0.476 ms
64 bytes from 192.168.1.66: seq=1 ttl=64 time=0.416 ms
64 bytes from 192.168.1.66: seq=2 ttl=64 time=0.410 ms
64 bytes from 192.168.1.66: seq=3 ttl=64 time=0.410 ms
64 bytes from 192.168.1.66: seq=4 ttl=64 time=3.112 ms
--- 192.168.1.66 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0.410/0.964/3.112 ms
>
Sends five ECHO_REQUEST packets of 56 bytes each to the host at
192.168.1.66.
>network ping count 10 size 100 192.168.1.1
Sends 10 ECHO_REQUEST packets of 100 bytes each to the host at 192.168.1.1.
The command returns data in the same form as above.
system reboot
Reboots the system either immediately or after the specified delay. Note that a reboot is required when
resetting the system to factory defaults (system factory-reset).
Synopsis system reboot [<seconds>]
Options <seconds> The number of seconds to delay the reboot.
Examples >system reboot
OK
>
The system is going down for reboot NOW! onelink-bridge-D8-80-39-62-A7-C5
Reboots the system immediately.
>system reboot 30
Reboots the system in 30 seconds. The response appears at the end of the delay.
71
Integrator's Complete Guide to the OneLINK Bridge AV Interface
system factory-reset
Gets or sets the factory reset status. When the factory reset status is on, the OneLINK device resets to
factory defaults on reboot.
Note
This does not reset the camera.
Synopsis system factory-reset { get | on | off}
Options get Returns the camera's current factory reset
status.
on Enables factory reset on reboot.
off Disables factory reset on reboot.
Examples >system factory-reset get
factory-reset (software): off
factory-reset (hardware): off
OK
>
Returns the factory reset status.
This evaluates the most recent system factory-reset on or off command, if
one has been received, then reads the rear panel DIP switches and returns the
status on if they are all in the down position.
>system factory-reset on
factory-reset (software): on
factory-reset (hardware): off
OK
>
Enables factory reset upon reboot.
Note
This command does not initiate a factory reset. The factory reset takes place on the
next reboot.
72
Integrator's Complete Guide to the OneLINK Bridge AV Interface
history
Returns the most recently issued commands from the current Telnet session. Since many of the programs
read user input a line at a time, the command history is used to keep track of these lines and recall historic
information.
Synopsis history <limit>
Options <limit> Integer value specifying the maximum number
of commands to return.
Examples history
Displays the current command buffer.
history 5
Sets the history command buffer to remember the last 5 unique entries.
Additional
information
You can navigate the command history using the up and down arrow keys.
This command supports the expansion functionality from which previous
commands can be recalled from within a single session. History expansion is
performed immediately after a complete line is read.
Examples of history expansion:
* !! Substitute the last command line.
* !4 Substitute the 4th command line (absolute as per ’history’ command)
* !-3 Substitute the command line entered 3 lines before (relative)
version
Returns the current firmware version of the OneLINK device.
Synopsis version
Example version
Returns current firmware version information in a form something like
this:
Audio 1.05-1.01
Commit a735fee1ab6270e693e2791b76a9bcbdf5bd36b5
HDLink RX4.6.1x0.01
System Version OneLINK Bridge 1.0.0
USB 01.00.017
Video 1.06
OK
>
73
Integrator's Complete Guide to the OneLINK Bridge AV Interface
help
Displays an overview of the CLI syntax.
Synopsis help
Example help
exit
Ends the command session and closes the socket.
Synopsis exit
Example exit
74
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Specifications
Capabilities
Video outputs Simultaneous HDMI, USB 3.0 and HD-SDI
USB 3.0 Streaming Originates USB 3.0 stream with
uncompressed video and
bidirectional stereo audio
IP Streaming Passes the stream from the
camera, if enabled
Audio inputs Two mic/line-level channels with
noise/echo cancellation;
phantom power available
Audio outputs Two balanced line-level audio
outputs
Mixing 10X8 audio mixer; audio is routable through all outputs
Control Features Web interface for configuration via browser
Telnet API for third-party external control
Ethernet and RS-232 control pass-through to camera
USB Human Interface Device (HID) for room audio controls
Maximum cable
length
328 ft (100m) Cat-5e cable; shielded Cat-6 recommended where EMI/RF interference is
an issue
Power, Physical, and Environmental
Input Power 48 VDC, 1.36 A Output Power to
Camera
12 VDC, 3.0 A
Height 1.72 in. (4.4 cm)/1U Width 8.38 in. (21.3 cm)
Depth 6.0 in. (15.2 cm) Weight 1.7 lb. (0.8 kg)
Operating/Storage
Temperature
32° to 104° F (0° to 40° C) Operating/Storage
Humidity
20% to 80% RH, non-
condensing
75
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Troubleshooting
When the Vaddio camera connected to the OneLINK device doesn't behave as you expect, check the color
of the camera's indicator light before you do anything else – but keep in mind that the camera's indicator
can be turned off in the administrative interface.
nPurple – booting or in standby (low power) mode.
nBlue – normal operation.
nRed – Tally function; the camera is on-air.
nBlinking red – fault condition.
nYellow – firmware update in progress.
Now check the OneLINK device's web interface for error messages. The EZIM (if one is used) tends to run
warm, which is normal. If the system detects that the temperature is too high, a temperature fault message
will appear at the top of the web interface page.
If neither of these reveal the problem, use this table to determine whether it's time to call Vaddio Technical
Support.
What is it doing? Possible causes Check and correct
Nothing.
The camera is not
receiving power.
The camera is not connected to the
EZIM (if an EZIM is used).
Plug the EZIM into the camera.
The OneLINK device's power pack is
not plugged in to main power, or the
EZIM (if one is used) is not connected to
the main OneLINK unit.
Plug the power pack into a wall outlet, or
connect the EZIM to its OneLINK base
unit.
At least one of the cables is bad. Replace the bad cable.
The wall outlet is not active. (Check by
finding out if it powers something else,
such as a laptop or phone charger.)
Plug the OneLINK power pack into a
different outlet.
"He's dead, Jim." Contact your reseller or Vaddio Technical
Support.
Camera does not
finish booting or
does not go to the
ready state.
Camera firmware may be out of date. Check the camera's firmware version;
update the camera firmware if necessary.
Possible cable issue. Test with shorter cables.
Try re-terminating the cable.
The camera is on,
but its web interface
is not available.
A cable is not connected. Make sure all network and OneLINK
cables are connected.
The network or OneLINK cable is bad. Replace the bad cable.
The camera is not using the IP address
you browsed to.
Vaddio cameras: Press the Data Screen
button on the remote to see the camera's
IP address.
No communication
with camera
Ethernet or RS-232 cable is connected
to the wrong port at one end.
Check the cables from the EZIM or
OneLINK device to the camera.
The wrong cable is connected (standard
Cat-5e cable where a custom Cisco
cable is needed, or vice-versa) or the
Be sure you are using the right cable.
If using a custom Cisco cable, be sure it
is connected according to the instructions
76
Integrator's Complete Guide to the OneLINK Bridge AV Interface
What is it doing? Possible causes Check and correct
custom cable is connected the wrong
direction.
on its labels.
The camera is not compatible with the
OneLINK device.
Be sure you are using your OneLINK
device with a compatible camera.
The camera is on
but not transmitting
video.
Possible cable length issue. Check the HDMI output from the camera
by connecting a display directly to it. If
video is good using a relatively short
cable directly to the display, then a better
grade of cable (Cat-6 or Cat-7) may
correct the problem.
Video drops out
repeatedly.
If this happens during PTZ movements,
the camera is not getting adequate
power.
Check how the camera behaves when it
and the attached EZIM are connected to
the main interface with a short (6 to 10 ft/
2 to 3 m) cable. If the camera performs
properly, then the problem is the length of
the cable from the main interface to the
EZIM. A better grade of cable (Cat-6 or
Cat-7) may correct the problem.
Possible cable inductance issue. Do not store excess cable by coiling it
neatly.
Best practice: Build cables to the required
length.
Video and audio
don't match up –
speech is audible
before the person on
the far end appears
to start speaking.
The audio signal is arriving before the
video signal, which is normal but not
desirable.
For the affected audio outputs (Line Out,
HDMI Out, or USB Record), enable
Delay and enter a value in milliseconds.
When connected to
a conferencing
codec: Far-end
audio drops out
periodically, and the
issue may intensify.
Echo cancellation is enabled on both the
codec and the OneLINK Bridge.
Disable echo cancellation on the
OneLINK Bridge.
Audio feedback or
echo that
intensifies.
Echo cancellation is disabled. If using the OneLINK Bridge with a
conferencing codec, enable echo
cancellation on the codec. Otherwise,
enable echo cancellation on the OneLINK
Bridge.
Polycom camera
does not respond to
the remote.
The OneLINK Bridge AV interface has
no IR forwarding.
Point the remote at the conferencing
codec.
77
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Operation, Storage, and Care
For smears or smudges on the product, wipe with a clean, soft cloth. Use a lens cleaner on the lens. Do not
use any abrasive chemicals.
Keep this device away from food and liquids.
Do not operate or store the device under any of the following conditions:
nTemperatures above 40°C (104°F) or below 0°C (32°F)
nHigh humidity, condensing or wet environments
nInclement weather
nSevere vibration
nLateral acceleration of more than 27G
nDry environments with an excess of static discharge
Do not attempt to take this product apart. There are no user-serviceable components inside.
78
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Compliance Statements and Declarations of Conformity
Statements are given separately for the OneLINK Bridge AV interface and the OneLINK HDMI EZCamera
Interface Module (EZIM).
OneLINK Bridge AV Interface
Compliance testing was performed to the following regulations:
FCC Part 15 (15.107, 15.109), Subpart B Class A
ICES-003, Issue 6, January 2016 Class A
EN 55024, 2010 Class A
EN 55032, 2012 Class A
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013 Safety
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A
EMC Directive 2014/30/EU Class A
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his/her own expense.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference including interference that
may cause undesired operation of the device.
Changes or modifications not expressly approved by Milestone AV Technologies can affect
emission compliance and could void the user’s authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numeriques de la classe A
préscrites dans le Règlement sur le brouillage radioélectrique édicte par le ministère des Communications
du Canada.
79
Integrator's Complete Guide to the OneLINK Bridge AV Interface
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions
and Immunity and meets the requirements for a Class A digital device. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2014/30/EU
EN 55032: 2012 Multimedia Equipment Emissions Requirements
EN 55024: 2010 IT Immunity Characteristics
EN 61000-4-2 + Amendments A1, A2 Electrostatic Discharge
EN 61000-4-3 + A1 Radiated Immunity
EN 61000-4-4 + Corrigendum Electrical Fast Transients
EN 61000-4-5 Surge Immunity
EN 61000-4-6 Conducted Immunity
EN 61000-4-8 Power Frequency Magnetic Field
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations
KN24 2008 (CISPR 24: 1997 + A1: 2000 +
A2: 2002)
IT Immunity Characteristics
EN 61000-4-2 Electrostatic Discharge
EN 61000-4-3 Radiated Immunity
EN 61000-4-4 Electrical Fast Transients
EN 61000-4-5 Surge Immunity
EN 61000-4-6 Conducted Immunity
EN 61000-4-8 Power Frequency Magnetic Field
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations
Low Voltage Directive 2014/35/EU
IEC 60950-1: 2005 (2nd Edition); Am 1: 2009
+ Am 2: 2013
Safety
EN 60950-1: 2006 + A11: 2009 + A1: 2010 +
A12: 2011 + A2: 2013
Safety
RoHS Directive 2011/65/EU
80
Integrator's Complete Guide to the OneLINK Bridge AV Interface
OneLINK HDMI EZCamera Interface Module (EZIM)
Compliance testing was performed to the following regulations:
nFCC Part 15 (15.107, 15. 109), Subpart B Class A
nICES-003, Issue 4: 2004 Class A
nEN 55022 A: 2006 + A1: 2007 Class A
nKN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A
nKN22 2008 (CISPR 22: 2006) Class A
nEMC Directive 2004/108/EC Class A
nEN 55024: A2: 2003 Class A
nEN 60950-1:2006+A11: 2009+A1: 2010+A12: 2011 Safety
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his/her own expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference including interference that may cause undesired operation of the
device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could
void the user’s authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte
par le ministère des Communications du Canada.
81
Integrator's Complete Guide to the OneLINK Bridge AV Interface
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions
and Immunity and meets the requirements for a Class A digital device. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC
EN 55022:2010 Conducted and Radiated Emissions
EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 Immunity
nEN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge
nEN 61000-4-3: 2006 + A1: 2008 Radiated Immunity
nEN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients
nEN 61000-4-5: 2006 Surge Immunity
nEN 61000-4-6: 2009 Conducted Immunity
nEN 61000-4-8: 2010 Power Frequency Magnetic Field
nEN 61000-4-11: 2004 Voltage Dips, Interrupts and Fluctuations
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) IT Immunity Characteristics
nEN 61000-4-2 Electrostatic Discharge
nEN 61000-4-3 Radiated Immunity
nEN 61000-4-4 Electrical Fast Transients
nEN 61000-4-5 Surge Immunity
nEN 61000-4-6 Conducted Immunity
nEN 61000-4-8 Power Frequency Magnetic Field
nEN 61000-4-11 Voltage Dips, Interrupts and Fluctuations
IEC 60950-1:2005 (2nd Edition); Am 1:2009 Safety
EN 60950-1: 2006+A11: 2009+A1: 2010+A12: 2011 Safety
82
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Warranty Information
See Vaddio Warranty, Service and Return Policies posted on support.vaddio.com for complete details.
Hardware* warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured
products. Vaddio warrants its manufactured products against defects in materials and workmanship for a
period of two years from the day of purchase, to the original purchaser, if Vaddio receives notice of such
defects during the warranty. Vaddio, at its option, will repair or replace products that prove to be
defective. Vaddio manufactures its hardware products from parts and components that are new or
equivalent to new in accordance with industry standard practices.
Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate
maintenance by the customer, customers applied software or interfacing, unauthorized modifications or
misuse, mishandling, operation outside the normal environmental specifications for the product, use of the
incorrect power supply, modified power supply or improper site operation and maintenance. OEM and
special order products manufactured by other companies are excluded and are covered by the
manufacturer’s warranty.
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the
unit is under warranty. If the product is out of warranty, Vaddio will test then repair the product or
products. The cost of parts and labor charge will be estimated by a technician and confirmed by the
customer prior to repair. All components must be returned for testing as a complete unit. Vaddio will not
accept responsibility for shipment after it has left the premises.
Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria
for repair costs and/or replacement. Vaddio Technical Support can be contacted by email at
support@vaddio.com or by phone at one of the phone numbers listed on support.vaddio.com.
Return Material Authorization (RMA) number: Before returning a product for repair or replacement
request an RMA from Vaddio’s technical support. Provide the technician with a return phone number, e-
mail address, shipping address, product serial numbers and original purchase order number. Describe the
reason for repairs or returns as well as the date of purchase. See the General RMA Terms and Procedures
section for more information. RMAs are valid for 30 days and will be issued to Vaddio dealers only. End
users must return products through Vaddio dealers. Include the assigned RMA number in all
correspondence with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when
returning the product. All products returned for credit are subject to a restocking charge without
exception. Special order product are not returnable.
Voided varranty: The warranty does not apply if the original serial number has been removed or if the
product has been disassembled or damaged through misuse, accident, modifications, use of incorrect
power supply, use of a modified power supply or unauthorized repair.
Shipping and handling: Vaddio will not pay for inbound shipping transportation or insurance charges or
accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound
shipping, transportation, and insurance charges for all items under warranty but will not assume
responsibility for loss and/or damage by the outbound freight carrier. If the return shipment appears
damaged, retain the original boxes and packing material for inspection by the carrier. Contact your carrier
immediately.
Products not under warranty: Payment arrangements are required before outbound shipment for all out of
warranty products.
83
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Index
A
acoustic echo cancellation 55
adjusting microphones 56
admin login 47, 51
AGC (automatic gain control) 55, 57
ambient noise, suppressing 55
anatomy of the EZCamera Interface Module 9
anatomy of the OneLINK device 7-8
API 65, 74
syntax help 74
audio 54-60, 66-69
controls 54-58
crosspoint gain 69
delay 57-58
feedback, preventing 55, 59
matrix, default 60
matrix, editing 60, 68
muting 54, 67
routing 60
volume 54, 66
Audio page (web) 53-60
automatic gain control 55
automatic inactivity time-out (web
session) 51
automatic NTP updating 50
B
backing up a configuration 61
browser compatibility 46
C
cable connectors 8-10
cables 2, 10, 17, 20, 26, 31, 33, 37, 44, 75
Cisco split 17, 26, 37, 44
maximum length 2, 10, 75
null-modem 20, 26, 37, 44
Polycom fan-out, codec, terminating 33
Polycom fan-out, codec, terminating |
Models.All OneLINK HDMI |
Models.All OneLINK HDMI [54] 31
capabilities 2
chairman override (microphone setting) 56
cheat sheet, web interface 48
cleaning 78
Codec Control Mode (Vaddio cameras) 16,
21, 31, 38
command execution delay 70
command history 73
compatibility, browsers 46
configuration, saving or restoring 61
configuring 13, 16, 21, 23, 31, 38, 45, 59
AEC reference 21, 38, 45, 59
connected RoboSHOT HDMI camera 23,
31, 38
connected Vaddio HDBaseT camera 13,
16, 21
connection diagram 11-20, 22-37, 40-44
block, HDBaseT camera 12
block, HDBaseT camera with codec 14
block, HDMI camera 22
block, HDMI camera with codec 29
Cisco Precision 40 25
Cisco Precision 40 with Cisco C20 40
Cisco Precision 40 with Cisco C40 41
Cisco Precision 40 with Cisco C60 41
Cisco Precision 40 with Cisco SX20 42
Cisco Precision 40 with Cisco SX80 43
Cisco Precision 60 26
Cisco Precision 60 with Cisco SX80 44
Cisco Precision HD 25
Cisco Precision HD with Cisco C20 40
Cisco Precision HD with Cisco C40 41
Cisco Precision HD with Cisco C60 41
Cisco Precision HD with Cisco SX20 42
Cisco Precision HD with Cisco SX80 43
Panasonic AW-HE130 27
Polycom EagleEye IV 24
Polycom EagleEye IV with Polycom RPG
310 32
Polycom EagleEye IV with Polycom RPG
500 32
Polycom EagleEye IV with Polycom RPG
700 33
RoboSHOT HDMI 23
RoboSHOT HDMI with Cisco C20 34
RoboSHOT HDMI with Cisco C40 35
RoboSHOT HDMI with Cisco C60 35
RoboSHOT HDMI with Cisco SX20 36
RoboSHOT HDMI with Cisco SX80 37
RoboSHOT HDMI with Polycom RPG
310 30
RoboSHOT HDMI with Polycom RPG
500 30
RoboSHOT HDMI with Polycom RPG
700 31
Sony SRG120 28
84
Sony SRG300 28
Vaddio HDBaseT 13
Vaddio HDBaseT with Cisco C20 17
Vaddio HDBaseT with Cisco C40 18
Vaddio HDBaseT with Cisco C60 18
Vaddio HDBaseT with Cisco SX20 19
Vaddio HDBaseT with Cisco SX80 20
Vaddio HDBaseT with Polycom RPG
310 15
Vaddio HDBaseT with Polycom RPG
500 15
Vaddio HDBaseT with Polycom RPG
700 16
visual conventions 11
connectors 8-11
identification 8-9
pin-outs, RS-232 11
customer-provided items 4, 6, 13, 15, 17, 23-
25, 27, 30, 32, 34, 39
cycle power to the camera 65
D
damage, preventing 10
date and time 50
default password 47
default settings, restoring 62, 72
DHCP 49
Diagnostics page (web) 64
dynamic range 57
E
echo cancellation 55, 57, 59
equalizer 57-58
equipment location information 51
F
factory defaults, restoring 62, 72
fault isolation 76
firmware update 63
firmware version 73
G
getting help 64
graphic equalizer 58
H
hardware reset 7
hardware specifications 75
Help page (web) 64
HID audio controls 52
high-pass filter adjustment (microphones) 57
hostname, assigning 50
I
importing a configuration 61
inactive sessions (web interface) 51
indicator lights 7, 76
information, equipment location 51
installation 11
mounting 11
IP address 47, 49
default 49
IP address display 7
IP streaming 52
IR forwarding 16, 31, 33
items you will need 4, 6, 13, 15, 17, 23-25, 27,
30, 32, 34, 39
K
key for connection diagrams 11
kits 1, 3-6, 12-15, 17, 22-25, 27, 29-30, 32, 34,
39
for Cisco cameras 25
for Cisco cameras with Cisco codecs 6,
22, 29, 39
for Panasonic cameras 4, 22, 27
for Polycom cameras 24
for Polycom cameras with Polycom
codecs 5, 22, 29, 32
for RoboSHOT HDMI cameras 4, 22-23
for RoboSHOT HDMI cameras with Cisco
codecs 6, 29, 34
for RoboSHOT HDMI cameras with Poly-
com codecs 5, 29-30
for Sony cameras 4, 22, 27
for Vaddio HDBaseT cameras 3, 12-13
for Vaddio HDBaseT cameras with Cisco
codecs 4, 14, 17
for Vaddio HDBaseT cameras with Poly-
com codecs 3, 14-15
L
line types in diagrams 11
locations of connectors 8-9
low-pass filter adjustment (microphones) 57
M
MAC address display 7
mic boost 57
85
Integrator's Complete Guide to the OneLINK Bridge AV Interface
microphones 53-56, 67
acoustic echo cancellation 55
adjusting volume 54
automatic gain control 55
chairman override 56
default settings 55
filter adjustments 57
muting 54, 67
noise cancellation 55
PEQ (parametric equalizer) 57
powering 53
speech lift adjustment 56
muting audio 54, 67
microphones 54
speakers 54
N
network configuration 49
changing 49
default 49
network configuration information (Telnet) 70
Networking page (web) 49-50
noise cancellation 55, 57
NTP server 50
O
operating environment 78
P
packing lists 3-6
999-9595-000/001/009 3
999-9620-000/001/009 5
999-9630-000/001/009 4
999-9640-000/001/009 5
999-9645-000/001/009 3
999-9660-000/001/009 6
999-9670-000/001/009 6
999-9675-000/001/009 4
999-9690-000/001/009 4
page 49-64
Audio 53-60
Diagnostics 64
Help 64
Networking 49-50
Room Labels 51
Security 51
Streaming 52
System 61-63
passwords 47, 51
changing 51
default 47
PEQ (parametric equalizer) 57
performance specifications 75
phantom power 53
physical and environmental specifications 75
pin-outs 11
for RS-232 connectors 11
ping command 71
power on/power off 46, 65
camera 65
powering microphones 53
problems, solving 76
product capabilities 2
product returns and repairs 83
product SKUs 1, 3-6
Q
quick reference, web interface 48
R
rebooting 62, 71
reset button location 7
restoring a configuration 61
restoring default settings 62, 72
RJ-45 connectors, recommendation 10
room information, adding 51
Room Labels page (web) 51
routing audio 60, 68
RS-232 adapter for Cisco products 20, 37, 44
RS-232 connector pin-out 11
S
saving a configuration 61
Security page (web) 51
settings, default, restoring 62, 72
software update 63
solving problems 76
speakers 54, 58, 67
adjusting for differing speech volumes 58
adjusting volume 54
equalizer 58
muting 54, 67
synchronizing audio with video 58
specifications 75
speech lift (microphone setting) 56
static IP address 49
storage environment 78
86
Integrator's Complete Guide to the OneLINK Bridge AV Interface
storing a configuration 61
Streaming page (web) 52
streaming settings 52
supported web browsers 46
synchronizing audio with video 58
System page (web interface) 61-62
System page (web) 63
system time 50
T
technical support 64
Telnet command help 74
Telnet session 65, 73-74
ending 74
history 73
temperature, operating and storage 78
time zone 50
troubleshooting 76
typographical conventions for command ref-
erence 65
U
updating firmware 63
USB device name 52
USB Record volume 54
USB streaming 52
V
version, firmware 73
volume controls 54, 66
W
warranty 10, 83
web browsers supported 46
web interface 48-64
Audio page 53-60
cheat sheet 48
Diagnostics page 64
Help page 64
Networking page 49-50
Room Labels page 51
Security page 51
Streaming page 52
System page 61-63
87
Integrator's Complete Guide to the OneLINK Bridge AV Interface
Vaddio is a brand of Milestone AV Technologies · www.vaddio.com · Phone 800.572.2011 /
+1.763.971.4400 · Fax +1.763.971.4464 · Email info@vaddio.com
Visit us at support.vaddio.com for firmware updates, specifications, drawings, manuals, and technical
support information. Vaddio, OneLINK, and RoboSHOT are trademarks or registered trademarks of
Milestone AV Technologies. The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI logo, are trademarkes or registered trademarks of HDMI Licensing LLC in the United States and
other countries. HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Exmor® is a trademark of Sony Corporation. All other brand names or marks are used for identification
purposes and are trademarks of their respective owners. In British Columbia, Milestone AV Technologies
ULC carries on business as MAVT Milestone AV Technologies ULC.
©2018 Milestone AV Technologies