Philips HQ6076/16 User Manual
Displayed below is the user manual for HQ6076/16 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
ENGLISH
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Trimmer
2 Trimmer release button
3 Socket for small plug
4 Adapter
5 Small plug
6 Battery symbol
7 On/off button
8 Shaving unit release button
9 Shaving unit
10 Protection cap
11 Pouch (not shown)
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Warning: Keep the adapter dry.
- This symbol means: Forbidden to rinse the
adapter under a running tap (Fig. 2).
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This symbol means: Forbidden to use in the
shower (Fig. 3).
- Warning: Do not use this appliance close to a
bathtub, shower or other containers lled with
water.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that
they do not play with the appliance.
Caution
- Do not use the shaver or the adapter if it is
damaged.
- Only use the adapter supplied.
- If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
Register your product and get support at
www.philips.com/welcome
4222.002.5412.1
HQ6076,HQ6075,HQ6073,
HQ6071,HQ6070
123 4
56 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24
- Charge, use and store the shaver at a
temperature between 5°C and 35°C.
- Warning: Remove the detachable cord from
the handheld part before cleaning this part in
water.
- Be careful with hot water. Always check if the
water is not too hot, to avoid burning your
hands.
- Water may leak from the socket at the
bottom of the appliance when you rinse it.
This is normal and not dangerous because all
electronics are enclosed in a sealed power unit
inside the shaver.
- Do not immerse the shaver in water or
another liquid
- Do not use the shaver in combination with
pre-shave lotions, creams, foams, gels or other
cosmetic products.
General
- This shaver can be safely cleaned under the tap.
- This symbol means: Suitable to be cleaned
under a running tap (Fig. 4).
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Compliance with standards
- This Philips appliance complies with all
standards regarding electromagnetic elds
(EMF). If handled properly and according to the
instructions in this user manual, the appliance
is safe to use based on scientic evidence
available today.
- This shaver complies with the applicable IEC
safety standards.
Charging
Make sure the appliance is switched off before you
start to charge it.
You can recharge the shaver between shaves, even
if the battery is not empty. This does not damage
the battery and prevents the battery from running
low during shaving.
Charging normally takes approx. 8 hours.
Do not leave the appliance connected to the
mains for more than 24 hours.
Charge indications
Charging
,When you start charging the shaver, the
battery symbol lights up (Fig. 5).
Battery running low
,HQ6076/HQ6075/HQ6073: When the
battery runs low, the red battery symbol
lights up. When you switch off the shaver, the
red battery symbol starts ashing. (Fig. 5)
,HQ6071/HQ6070: There is no indication
that the battery is low. The appliance switches
off automatically when the battery
is completely empty.
Charging the appliance
Charge the appliance when the red battery symbol
lights up or ashes (HQ6076/HQ6075/HQ6073)
or when the motor stops or starts running more
slowly (HQ6071/HQ6070).
1 Put the appliance plug in the shaver (Fig. 6).
2 Put the adapter in the wall socket.
3 When the battery is fully charged, remove
the adapter from the wall socket and pull
the appliance plug out of the shaver.
Cordless shaving time
A fully charged shaver has a cordless shaving time
of up to 40 minutes.
Using the appliance
Shaving
1 Press the on/off button once to switch on
the shaver.
The light ring lights up.
2 Move the shaving heads quickly over your
skin, making both straight and circular
movements (Fig. 7).
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3 Press the on/off button once to switch on the
shaver.
4 To prevent damage to the shaving unit, put
the protection cap on the shaver after every
use (‘click’) (Fig. 8).
Trimming
For grooming sideburns and moustache.
1 Open the trimmer by pushing the slide
upwards (Fig. 9).
The trimmer can be activated while the motor is
running.
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
The easiest and most hygienic way to clean the
appliance is to rinse the shaving unit and the hair
chamber with hot water every time you have used
the appliance.
For thorough cleaning of the shaving heads, we
advise you to use Philips Shaving Head Cleaning
Spray HQ110.
Every day: shaving unit and hair
chamber
Warning: Remove the detachable cord from the
handheld part before cleaning this part in water.
Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
1 Switch off the shaver, remove the adapter
from the wall socket and pull the appliance
plug out of the shaver.
2 Press the release button (1) and open the
shaving unit (2) (Fig. 10).
3 Clean the shaving unit and the hair chamber
by rinsing them under a hot tap for some
time (Fig. 11).
Make sure the inside of the shaving unit and the
hair chamber have been cleaned properly.
4 Rinse the outside of the appliance (Fig. 12).
5 Close the shaving unit and shake off excess
water.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
6 Open the shaving unit again and leave it open
to let the appliance dry completely (Fig. 13).
You can also clean the hair chamber without water
by using the brush supplied.
Every six months: shaving heads
1 Open the shaving unit.
You can also pull the shaving unit off the shaver for
easier cleaning.
2 To remove the shaving heads, do the
following.
- HQ6076/HQ6075: Remove the retaining
frame and take out the shaving heads. (Fig. 14)
- HQ6073/HQ6071/HQ6070: Open the shaving
unit, turn the wheel anticlockwise (1) and
remove the retaining frame (2). Then take out
the shaving heads (Fig. 15).
3 Clean the cutters and guards with the brush
supplied (your shaving heads may differ from
the one shown in the gure) (Fig. 16).
Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it
may take several weeks before optimal shaving
performance is restored.
4 Put the shaving heads back into the shaving
unit and reassemble the shaving unit (Fig. 17).
- HQ6076/HQ6075: Make sure that the
projections of the shaving heads t into the
recesses when you put them back. Then place
the retaining frame back into the shaving unit.
- HQ6073/HQ6071/HQ6070: Put the shaving
heads back into the shaving unit. Put the
retaining frame back into the shaving unit and
turn the lock clockwise (your shaving heads
may differ from the one shown in the gure).
Note: If you removed the shaving unit from the
shaver, reattach it. First insert the hinge of the shaving
unit into the slot in the rim of the hair chamber and
then push the shaving unit home until it locks into
place (‘click’). (Fig. 18)
5 Close the shaving unit.
Trimmer
Clean the trimmer every time you have used it.
1 Switch off the shaver, remove the adapter
from the wall socket and pull the appliance
plug out of the shaver.
2 Clean the trimmer with the brush
supplied (Fig. 19).
3 Lubricate the trimmer teeth with a drop of
sewing machine oil every six months (Fig. 20).
Storage
- To prevent damage to the shaving unit, put the
protection cap on the shaver (‘click’) (Fig. 8).
- HQ6076/HQ6075/HQ6073: Store the
appliance in the pouch.
Replacement
To maintain optimal shaving results, replace the
shaving heads every two years.
Replace damaged or worn shaving heads with
HQ8 Precise Cutting System Shaving Heads.
1 Switch off the shaver, remove the adapter
from the wall socket and pull the appliance
plug out of the shaver.
2 Open the shaving unit.
You can also pull the shaving unit off the shaver.
3 To remove the shaving heads, do the
following.
Problem Solution
The shaver
does not
shave as
well as it
used to.
You may not have cleaned
the appliance properly. Clean
the shaving heads thoroughly
(see chapter ‘Cleaning and
maintenance’).
Long hairs may be obstructing the
shaving heads. Clean the cutters
and guards properly with the brush
supplied (see chapter ‘Cleaning and
maintenance’).
The shaving heads may be
damaged or worn. Replace
the shaving heads (see chapter
‘Replacement’).
The shaver
does not
switch on
when I
press the
on/off
button.
The battery may be empty.
Recharge the battery (see chapter
‘Charging’).
The
shaving unit
has come
off the
shaver.
Simply reattach the shaving unit
by pressing it onto the shaver (see
chapter ‘Replacement’, step 5).
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 22).
- The built-in rechargeable shaver battery
contains substances that may pollute the
environment. Always remove the battery
before you discard and hand in the shaver at
an ofcial collection point. Dispose of the
battery at an ofcial collection point for
batteries. If you have trouble removing
the battery, you can also take the shaver
to a Philips service centre. The staff of this
centre will remove the battery for you and
will dispose of it in an environmentally safe
way (Fig. 23).
Disposal of the battery
Only remove the battery if it is completely empty.
1 Remove the adapter from the wall socket and
pull the appliance plug out of the shaver.
2 Let the shaver run until it stops, undo the
screws and open the shaver (Fig. 24).
3 Remove the battery.
Do not connect the shaver to the mains again
after the battery has been removed.
Guarantee and service
If you need information or if you have a problem,
please visit the Philips website at www.philips.
com/support or contact the Philips Consumer
Care Centre in your country. You nd its phone
number in the worldwide guarantee leaet. If there
is no Consumer Care Centre in your country, go
to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards) are
not covered by the terms of the international
guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Centre in your country.
- HQ6076/HQ6075: Remove the retaining
frame and take out the shaving heads. (Fig. 14)
- HQ6073/HQ6071/HQ6070: Open the shaving
unit, turn the wheel anticlockwise (1) and
remove the retaining frame (2). Then take out
the shaving heads (Fig. 15).
4 Put the new shaving heads in the shaving unit
and reassemble the shaving unit (Fig. 17).
- HQ6076/HQ6075: Make sure that the
projections of the shaving heads t into the
recesses when you put them in the shaving
unit. Then place the retaining frame back into
the shaving unit.
- HQ6073/HQ6071/HQ6070: Put the shaving
heads in the shaving unit. Put the retaining
frame back into the shaving unit and turn the
lock clockwise (your shaving heads may differ
from the one shown in the gure).
Note: If you removed the shaving unit from the
shaver, reattach it. First insert the hinge of the shaving
unit into the slot in the rim of the hair chamber and
then push the shaving unit home until it locks into
place (‘click’). (Fig. 18)
5 Close the shaving unit.
Ordering accessories
To retain the top performance of your shaver,
make sure you clean it regularly and replace its
shaving heads at the recommended time.
To purchase accessories for your shaver,
please visit our online shop at
www.shop.philips.com/service. If the online
shop is not available in your country, go to your
Philips dealer or a Philips service centre. If you have
any difculties obtaining accessories for your shaver,
please contact the Philips Consumer Care Centre
in your country. You nd its contact details in the
worldwide guarantee leaet.
Shaving heads
- We advise you to replace your shaving heads
every two years. Always replace with the
appropriate shaving heads for your type of
shaver (Fig. 21).
Cleaning
- Use Cleaning Spray HQ110 to clean the
shaving heads thoroughly.
Accessories available for this shaver
HQ8 Precise Cutting System Shaving Heads.
HQ8505 powerplug.
HQ110 Philips Shaving Head Cleaning Spray.
6 再一次打開電鬍刀組並保持開啟，讓電鬍
刀完全晾乾。(圖13)
您也可以不用水，而用隨附的刷子來清潔鬍
渣室。
每半年：電鬍刀刀頭
1 打開電鬍刀組。
您也可以將電鬍刀組從電鬍刀抽出，以方便
清潔。
2 若要拆卸電鬍刀刀頭，請執行下列步驟。
-HQ6076/HQ6075：移除固定架，並取出
電鬍刀刀頭。 (圖 14)
-HQ6073/HQ6071/HQ6070：打開電鬍刀
組，以逆時針方向轉動轉盤 (1)，並拆下固
定架(2)。然後取出電鬍刀刀頭。 (圖 15)
3 請使用隨附的毛刷清潔刀具及刀網(您的
電鬍刀頭外觀可能與圖示不同)。(圖16)
因為刀片及刀網是成對的一組，請勿一次清潔
一組以上。如果您不小心將刀片及刀網混在一
起，可能要花幾週的時間才能恢復最理想的刮
鬍效果。
4 將電鬍刀刀頭裝回電鬍刀組，並且重新組
裝電鬍刀組。(圖17)
-HQ6076/HQ6075：放回電鬍刀刀頭時，
請確定其凸出部分符合凹陷處，然後將固
定架裝回電鬍刀組上。
-HQ6073/HQ6071/HQ6070：將電鬍刀刀
頭裝回電鬍刀組。將固定架裝回電鬍刀組
上，並以順時針方向轉動鎖扣 (您的電鬍
刀頭外觀可能與圖示不同)。
注意：如果您將電鬍刀組從電鬍刀上取下，
請重新裝回。先將電鬍刀組的鉸鏈插回鬍渣室
邊緣的槽孔中，並將電鬍刀組推回原位(會聽
見「喀噠」一聲)，即可裝回電鬍刀組。
(圖18)
5 關上電鬍刀組。
修整刀
每次使用鬢角刀後，請進行清潔。
1 關閉電鬍刀電源，將變壓器從電源插座拔
除，並將產品電源線自電鬍刀上拔下。
2 使用隨附於電鬍刀的刷子來清潔鬢角刀。
(圖19)
3 請每6個月以一滴縫紉機油來潤滑鬢角刀
的刀齒。(圖20)
收納
-為避免損害電鬍刀組，請蓋上電鬍刀保護
蓋 (會聽見「喀噠」一聲)。 (圖 8)
-HQ6076/HQ6075/HQ6073：將本產品存
放在收納袋中。
無線刮鬍時間
完全充電的電鬍刀可在不插電的狀態下持續刮
鬍約 40 分鐘。
使用此產品
刮鬍
1 按一下開關(on/off)按鈕，開啟電鬍刀電
源。
指示燈會亮起。
2 將電鬍刀刀頭在皮膚上快速移動，請同時
用直線及畫圓的方式來移動。(圖7)
乾刮可獲得最佳的刮鬍效果。
您的皮膚可能需要 2 到 3 週的時間才能完全
適應飛利浦電鬍刀系統。
3 按一下開關(on/off)按鈕，開啟電鬍刀電
源。
4 為避免損害電鬍刀組，每次使用後請蓋上
電鬍刀保護蓋(會聽見「喀噠」一聲)。
(圖8)
修剪
適合刮除鬢角及髭鬍。
1 向上推電源開關鈕即可打開鬢角刀。
(圖9)
馬達轉動時即可使用鬢角刀。
清潔與維護
定期清潔以維持較佳的刮鬍效果。
清潔本產品最簡單、最衛生的方式，是每次使
用後用熱水沖洗電鬍刀頭與鬍渣室。
若要徹底清潔電鬍刀刀頭，我們建議您使用飛
利浦電鬍刀刀頭噴霧清潔劑 HQ110。
每天：清理電鬍刀組與鬍渣室。
警示：請先取下握把零件的可拆式電源線，再
於水中清洗此零件。
請小心使用熱水。隨時檢查熱水是否太燙，以
避免手部燙傷。
1 關閉電鬍刀電源，將變壓器從電源插座拔
除，並將產品電源線自電鬍刀上拔下。
2 按下釋放鈕(1)並打開電鬍刀頭(2)。
(圖10)
3 偶爾在水龍頭下以熱水沖洗清潔電鬍刀組
與鬍渣室。(圖11)
確定刀頭部分與鬍渣室已充分清洗乾淨。
4 沖洗本產品外部。(圖12)
5 蓋上電鬍刀組，並將多餘的水甩乾。
切勿使用毛巾或紙巾擦乾電鬍刀組，因為此舉
可能會造成電鬍刀刀頭損害。
-請勿將電鬍刀浸在水或其他液體中
-使用電鬍刀時，請勿搭配任何刮鬍水、乳
霜、乳液、凝露或其他其他化妝品。
一般
-此電鬍刀可在水龍頭下安全地清洗。
-此符號表示：適合在水龍頭下清洗。
(圖 4)
-轉換器可將 100-240 伏特的電壓轉換為低
於 24 伏特的安全低電壓。
符合標準
-本飛利浦產品符合電磁波
(Electromagnetic fields，EMF) 所有相關
標準。只要使用方式正確並依照本使用手
冊之說明進行操作，根據現有的科學研究
資料，使用本產品並無安全顧慮。
-本電鬍刀符合適用的 IEC 安全標準。
充電
在您開始進行充電之前，請確定將電鬍刀的電
源關閉。
即使電池電量尚未用盡，您也可以在兩次刮鬍
間將電鬍刀重新充電。這麼做並不會損壞電
池，並可在刮鬍時避免電池電力不足。
充電一般約需 8 小時。
不要讓電鬍刀連續連接電源插座超過24小
時。
充電指示
充電
,當您開始為電鬍刀充電時，電池符號會亮
起。(圖5)
電池電力不足
,HQ6076/HQ6075/HQ6073：電池快沒電
時，紅色的電池符號會亮起。關閉電鬍
刀電源時，紅色的電池符號則會開始閃
爍。(圖5)
,HQ6071/HQ6070：電池電力不足時並不
會提示。電力用盡時會自動關閉電源。
充電
在電池符號亮起紅燈或閃爍時 (HQ6076/
HQ6075/HQ6073)，或者馬達停止運轉或轉
速變慢時 (HQ6071/HQ6070)，請為本產品充
電。
1 將電源線的一端插在電鬍刀機體的電源插
孔中。(圖6)
2 將轉換器插入插座。
3 電池完全充電後，將變壓器從電源插座拔
除，並將產品電源線自電鬍刀上拔下。
繁體中文
簡介
感謝您購買本產品並歡迎加入飛利浦！請於
www.philips.com/welcome 註冊您的產品，
以善用飛利浦提供的支援。
一般說明 (圖 1)
1 修整刀
2 修整刀釋放鈕
3 小插頭插座
4 轉換器
5 小插頭
6 電池符號
7 開/關按鈕
8 刮鬍刀頭組釋放按鈕
9 除毛刀頭組
10 保護蓋
11 旅行袋 (說明書中未顯示)
重要事項
在使用本產品前，請先仔細閱讀本使用手冊，
並保留使用手冊以供日後參考。
危險
-警示：請保持轉換器乾燥。
-此符號表示：禁止在水龍頭下清洗轉換
器。 (圖 2)
警示
-轉換器內含一個變壓器。請勿切斷轉換器
而以其他插頭取代，否則會造成危險。
-此符號表示：禁止在淋浴時使用。 (圖 3)
-警告：請勿在浴缸、淋浴間或其他裝水容
器附近使用本產品。
-基於安全考慮，在缺乏監督及適當指示之
下，本產品不適用於孩童及任何身體、知
覺、或心理功能障礙者，或缺乏使用經驗
及知識者。
-請勿讓孩童使用本產品或將本產品當成玩
具。
警告
-電鬍刀或變壓器損壞時，請勿使用。
-只能使用產品所附的充電器。
-如果轉換器損壞，請務必使用原型號的轉
換器進行更換，以免發生危險。
-請於 5°C 到 35°C 間充電、使用並存放
電鬍刀。
-警示：請先取下握把零件的可拆式電源
線，再於水中清洗此零件。
-請小心使用熱水。隨時檢查熱水是否太
燙，以避免手部燙傷。
-在您沖洗時，水可能會從電鬍刀底部的插
孔流出。此為正常現象，不會造成危險，
因為所有的電子零件都密封於電鬍刀機殼
內。
問題 解決方法
電鬍刀不
像平常一
樣運作。
您可能未妥善清潔電鬍刀。請
徹底清潔電鬍刀刀頭 (請參閱
「清潔與維護」單元)。
過長的鬍鬚卡住電鬍刀刀頭。
請使用隨附的毛刷清潔刀具及
刀網 請參閱「清潔與維護」
單元)。
電鬍刀刀頭毀壞或磨損，請更
換電鬍刀頭 (請參閱「更換」
單元)。
我按下開/
關按鈕時，
電鬍刀沒
有開始運
作。
電池可能沒電了，請為電池充
電 (請參閱「充電」單元)。
電鬍刀組脫
離電鬍刀
只要將電鬍刀組壓入電鬍刀，
重新裝上即可 (請參閱「更
換」單元的步驟 5)。
本電鬍刀配件
HQ8 精確的切割系統電鬍刀頭。
HQ8505 電源插頭。
HQ110 飛利浦電鬍刀刀頭噴霧清潔劑。
環境保護
-本產品使用壽命結束時請勿與一般家庭廢
棄物一併丟棄。請將該產品放置於政府指
定的回收站，此舉能為環保盡一份心力。
(圖 22)
-本電鬍刀使用的充電電池含有會污染環境
的物質。在丟棄本用品前，或是將該產品
放到政府指定回收站前，請務必卸除電
池。將電池送到政府指定的電池回收站。
若您在拆卸電池時遇到問題，可將本用品
帶到飛利浦授權服務中心。服務中心會為
您卸下電池，並以對環境無害的方式處理
電池。 (圖 23)
電池棄置
必須將電池電力完全耗盡後才能拆卸電池。
1 將變壓器自電源插座拔出，並將產品插頭
從電鬍刀拔下。
2 讓電鬍刀持續運轉直到完全停止為止，拆
下螺絲並拆開電鬍刀本體。(圖24)
3 取出電池。
取出電池後，請不要再把電鬍刀接上電源插
座。
保固與服務
若您需要相關資訊或是有任何問題，請瀏覽飛
利浦網站：www.philips.com/support，或者
聯絡您當地國家的飛利浦客戶服務中心，您可
以在全球保證書上找到聯絡電話。若您當地國
家沒有客戶服務中心，請洽詢當地的飛利浦
經銷商。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損性，因
此不在全球保固範圍內。
故障排除
本章概述您使用本產品時最常遇到的問題。如
果您無法利用以下資訊解決您遇到的問題，請
造訪 www.philips.com/support，上面列有常
見問題清單，或聯絡您所在國家/地區的客戶
服務中心。
更換
為維持最佳的刮鬍效果，請每兩年更換一次電
鬍刀刀頭。
更換損壞或磨損的電鬍刀頭時，請使用 HQ8
飛利浦電鬍刀頭。
1 關閉電鬍刀電源，將變壓器從電源插座拔
除，並將產品電源線自電鬍刀上拔下。
2 打開電鬍刀組。
您也可以將電鬍刀組從電鬍刀抽出。
3 若要拆卸電鬍刀刀頭，請執行下列步驟。
-HQ6076/HQ6075：移除固定架，並取出
電鬍刀刀頭。 (圖 14)
-HQ6073/HQ6071/HQ6070：打開電鬍刀
組，以逆時針方向轉動轉盤 (1)，並拆下固
定架(2)。然後取出電鬍刀刀頭。 (圖 15)
4 將新的電鬍刀刀頭裝上電鬍刀組，並且重
新組裝電鬍刀組。(圖17)
-HQ6076/HQ6075：將電鬍刀刀頭放回電
鬍刀組時，請確定電鬍刀刀頭的凸出部分
符合凹陷處，然後將固定架裝回電鬍刀組
上。
-HQ6073/HQ6071/HQ6070：將電鬍刀刀
頭裝上電鬍刀組。將固定架裝回電鬍刀組
上，並以順時針方向轉動鎖扣 (您的電鬍
刀頭外觀可能與圖示不同)。
注意：如果您將電鬍刀組從電鬍刀上取下，
請重新裝回。先將電鬍刀組的鉸鏈插回鬍渣室
邊緣的槽孔中，並將電鬍刀組推回原位(會聽
見「喀噠」一聲)，即可裝回電鬍刀組。
(圖18)
5 關上電鬍刀組。
訂購配件
若要維持電鬍刀的最佳效能，請務必定期清潔
電鬍刀，並於建議的時間更換電鬍刀刀頭。
如需購買電鬍刀的配件，請造訪我們的線上商
店：www.shop.philips.com/service。若您所
在國家/地區沒有線上商店，請聯絡您的飛利
浦經銷商或飛利浦服務中心。如果無法取得電
鬍刀的配件，請聯絡您所在國家的飛利浦客
戶服務中心。如需詳細聯絡資料，請參閱全球
保證書。
電鬍刀刀頭
-我們建議您每兩年更換一次電鬍刀刀頭。
更換時請一律使用適合您所擁有之電鬍刀
類型的電鬍刀刀頭。 (圖 21)
清潔
-使用噴霧清潔劑 HQ110 徹底清潔電鬍刀
刀頭。