Philips PQ182/16 User Manual
Displayed below is the user manual for PQ182/16 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Hair chamber
5 On/off slide
6 Front panel
7 Charging light
8 Foldable plug
9 Release button of foldable plug
10 Retaining frame
11 Central spring of retaining frame
12 Cutter
13 Guard
14 Cleaning brush
15 Philips Cleaning spray (HQ110)
(optional)
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Keep the appliance dry.
- This symbol means: Forbidden to clean
under a running tap (Fig. 2).
Warning
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with the
appliance.
Caution
- Use and store the appliance at a
temperature between 5°C and 35°C.
- Only use the cleaning brush supplied.
- Make sure the cleaning brush
remains clean.
Electromagnetic elds (EMF)
This Philips appliance complies with all
standards regarding electromagnetic elds.
If handled properly and according to
the instructions in this user manual, the
appliance is safe to use based on scientic
evidence available today.
Charging
Charge the appliance when the motor
stops or starts running slower.
When you charge the shaver for the rst
time or after a long period of disuse, let it
charge continuously for 12 hours. Charging
normally takes approx. 10 hours.
Do not leave the appliance connected to
the mains for more than 24 hours.
1 Switch off the shaver before you start
charging it.
2 Press the release (1) button and
fold out the foldable plug (2)
(‘click’) (Fig. 3).
3 Insert the foldable plug unit into the
wall socket (Fig. 4).
,The charging light goes on to indicate
that the appliance is charging (Fig. 5).
4 Remove the shaver from the wall
socket when the battery is fully
charged.
5 Press the release button (1) and
fold the foldable plug back into the
appliance (2) (‘click’) (Fig. 6).
Note: The charging light does not go out or
change colour when the appliance is fully
charged.
Cordless shaving time
A fully charged shaver has a cordless shaving
time of approximately 30 minutes.
Using the appliance
The shaver cannot be used directly from
the mains.
1 Remove the protection cap.
2 Push the on/off slide upwards to
switch on the shaver (Fig. 7).
3 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 8).
Note: Shave on a dry face only. Do not use the
shaver in combination with gel, foam or water.
PQ197, PQ192, PQ187, PQ182
Register your product and get support at
www.philips.com/welcome
4222.002.5443.1
31/10/2012
1234
567
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
26 27 28
29 30
Note: Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
4 Push the on/off slide downwards to
switch off the shaver.
5 Clean the shaver after every
shave, see chapter ‘Cleaning and
maintenance’.
6 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 9).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol
or acetone to clean the appliance.
Clean the shaver after every shave to
guarantee better shaving performance. For
the best cleaning result, we advise you to
use Philips Cleaning Spray (HQ110). Ask
your Philips dealer for information.
After every shave: shaving unit
and hair chamber
1 Switch off the shaver.
2 Clean the top of the appliance with
the cleaning brush supplied (Fig. 10).
3 Pull the shaving unit straight up off the
shaver (Fig. 11).
4 Clean the inside of the shaving unit
with the cleaning brush (Fig. 12).
5 Clean the hair chamber with the
cleaning brush (Fig. 13).
6 Put the shaving unit back onto the
shaver (Fig. 14).
Every two months: shaving heads
Note: Do not use cleaning agents or alcohol
to clean the shaving heads. Only use Philips
Cleaning Spray (HQ110).
1 Switch off the shaver.
2 Pull the shaving unit straight up off the
shaver (Fig. 15).
3 To remove the retaining frame,
push the sides of the central spring
towards each other (1).Then lift the
retaining frame out of the shaving unit
(2) (Fig. 16).
4 Slide the shaving heads out of the
retaining frame. Remove and clean
one shaving head at a time. Each
shaving head consists of a cutter and a
guard (Fig. 17).
Note: Do not clean more than one cutter
and guard at a time, since they are matching
sets. If you accidentally mix up the cutters
and guards, it may take several weeks before
optimal shaving performance is restored.
5 Remove the guard from the
cutter (Fig. 18).
6 Clean the cutter with the short-
bristled side of the cleaning brush.
Brush carefully in the direction of the
arrows (Fig. 19).
7 Clean the guard with the long-bristled
side of the cleaning brush (Fig. 20).
8 Put the cutter back into the guard
after cleaning (Fig. 21).
9 Slide the shaving heads back into the
retaining frame (Fig. 22).
10 Put the retaining frame back into the
shaving unit (‘click’) (Fig. 23).
11 Put the shaving unit back onto the
shaver (Fig. 24).
Storage
Keep the appliance dry.
Use and store the appliance at a
temperature between 5°C and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 25).
Replacement
Replace the shaving heads every two years
for optimal shaving results.
Replace damaged or worn shaving heads
with Philips shaving heads only (HQ4+ for
China or HQ56 for the rest of the world).
For instructions on how to remove the
shaving heads, see chapter ‘Cleaning and
maintenance’, section ‘Every two months:
shaving heads’.
Accessories
To retain top performance of your shaver,
make sure you clean it regularly and replace
its shaving heads at the recommended time.
Shaving heads
- We advise you to replace your shaving
heads every two years. Always replace
them with Philips shaving heads only
(HQ4+ for China or HQ56 for the
rest of the world) (Fig. 26).
Cleaning
- Use Philips Cleaning Spray (HQ110) to
clean the shaving heads thoroughly.
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 27).
- The built-in rechargeable battery
contains substances that may pollute
the environment. Always remove the
battery before you discard and hand
in the appliance at an ofcial collection
point. Dispose of the battery at an
ofcial collection point for batteries.
If you have trouble removing the
battery, you can also take the appliance
to a Philips service centre. The staff
of this centre will remove the battery
for you and will dispose of it in an
environmentally safe way (Fig. 28).
Removing the rechargeable
battery
Only remove the rechargeable battery
when it is completely empty.
1 Make sure the appliance is
disconnected from the mains.
2 Let the shaver run until it stops, undo
the screw on the back of the shaver
(1) and lift the back panel off the
shaver (2) (Fig. 29).
3 Remove the rechargeable
battery (Fig. 30).
Do not connect the shaver to the mains
again after you have removed the battery.
Guarantee and support
If you need service or support, please visit
www.philips.com/support or read the
separate worldwide guarantee leaet.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact the
Consumer Care Centre in your country.
Problem Possible
cause
Solution
The
shaver
does not
shave as
well as it
used to.
The
shaving
heads are
dir ty. You
have not
cleaned the
shaver well
enough
or you
have not
cleaned it
for a long
time.
Clean the
shaver thor-
oughly before
you continue
shaving. See
chapter
‘Cleaning and
maintenance’.
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the cleaning
brush supplied.
See chapter
‘Cleaning and
maintenance’,
section ‘Every
two months:
shaving heads’.
The
shaving
heads are
damaged
or worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
Problem Possible
cause
Solution
The
shaver
does not
work
when I
push the
on/off
slide up-
wards.
The
battery is
empty.
Recharge the
battery. See
chapter ‘Charg-
ing’.
My
skin is
irritated
after
shaving.
Your skin
needs time
to get
used to
the Philips
shaving
system.
Skin irritation
during the rst
2-3 weeks of
use is pos-
sible. After this
period, the skin
irritation usu-
ally disappears.
The
rotation
speed of
the shav-
ing heads
is slower
than
usual.
Too much
dirt has
collected
in the
shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The
battery is
empty
Recharge the
battery. See
chapter ‘Charg-
ing’.
The ap-
pliance
makes a
strange
noise.
Too much
dirt has
collected
in the
shaving
heads.
Clean the
shaving heads.
After cleaning,
lubricate the
central point
on the inside of
the guards with
Philips Cleaning
Spray(HQ110).
See chapter
‘Cleaning and
maintenance’.
The
shaving
heads are
damaged
or worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
清洁和保养
不要使用钢丝球、研磨性清洁剂或腐
蚀性液体（例如汽油或丙酮）来清洁
产品。
每次剃须后均应清洁剃须刀，以保证
更好的剃须效果。为了获得最佳的清
洁效果，建议您使用飞利浦清洁喷雾
剂 (HQ110)。有关详情，请咨询飞利浦
经销商。
每次剃须后：清洗剃须刀头部件和
胡茬储藏室
1 关闭剃须刀。
2 用随附的清洁刷清洁产品顶部。
(图10)
3 垂直向上拉动剃须刀头部件，
将其从剃须刀中拉出。(图11)
4 用清洁刷清洁剃须刀头部件的内侧。
(图12)
5 用清洁刷清洁胡茬储藏室。(图13)
6 将剃须刀头组件重新安装到剃须刀上。
(图14)
每两个月：清洁剃须刀头
注意：请勿使用清洁剂或酒精来清洁
剃须刀头。只能使用飞利浦清洁喷雾剂
(HQ110)。
1 关闭剃须刀。
2 垂直向上拉动剃须刀头部件，
将其从剃须刀中拉出。(图15)
3 要取下固定架，请捏拢中央弹簧的
两侧(1)。然后向上提起固定架，
将其从剃须刀头部件中取出(2)。
(图16)
4 将剃须刀头滑离固定架。一次取下
并清洁一个剃须刀头。每个剃须刀
头包含一组刀片和网罩。(图17)
注意：不要同时清洁多组刀片和网罩，
因为它们都是相互匹配的。如果不小心
将刀片和网罩弄混，则需要数周时间才
能恢复产品的最佳剃须性能。
5 从刀片上卸下网罩。(图18)
6 用清洁刷的短毛一侧清洁刀片。
按箭头方向小心地清洁。(图19)
7 用清洁刷的长毛一侧清洁网罩。
(图20)
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！为了
您能充分享受飞利浦所提供的支持，
请在 www.philips.com/welcome 上注
册您的产品。
基本说明 (图 1)
1 保护盖
2 剃须刀头
3 剃毛刀头部件
4 毛发储藏室
5 开/关滑钮
6 前面板
7 充电指示灯
8 折叠式插头
9 折叠式插头的释放钮
10 固定架
11 固定架的中央弹簧
12 刀片
13 网罩
14 清洁刷
15 飞利浦清洁喷雾剂 (HQ110)
（可选）
注意事项
使用产品之前，请仔细阅读本用户手
册，并妥善保管以供日后参考。
危险
-保持器具干燥。
-警告符号注释：禁止用在打开的水
龙头下进行清洗。 (图 2)
警告
-肢体不健全、精神有障碍及缺乏相
关经验和知识的人（包括儿童）必
须在监护人的监督及指导下使用。
-请照看好儿童，本产品不能用于
玩耍。
注意
-必须在 5°C 至 35°C 之间的温度
下使用和存放本产品。
-仅限使用随附的清洁刷。
-确保清洁刷保持洁净。
电磁场 (EMF)
本飞利浦产品符合电磁场所有相关标准。
就目前的科学研究证明，如果正确使用
并按照本用户手册中的说明进行操作，
本产品是安全的。
充电
当马达停转或转速开始下降时，为产
品充电。
如果是第一次充电，或是长时间未使用
后充电，应将其连续充电 12 小时。充
电通常需约 10 小时。
不要将本产品与电源接通超过24小时。
1 开始充电前，请关闭剃须刀。
2 按下释放钮(1)，并展开折叠式插头
(2)（可听到“咔哒”一声）。
(图3)
3 将折叠式插头插入电源插座。
(图4)
,充电指示灯亮起，表示剃须刀正在
充电。(图5)
4 请在电池完全充电后，从插座上取
下剃须刀。
5 按下释放按钮(1)并将折叠式插头
重新折叠到产品内部(2)（可听到“
咔哒”一声）。(图6)
注意：产品完全充电时，充电指示灯不
会熄灭或更改颜色。
不接电源的剃须时间
完全充电的剃须刀在不连接电源的情况
下最长可使用达 30 分钟。
使用本产品
剃须刀不能连在电源上直接使用。
1 取下保护盖。
2 向上推动开/关滑钮以接通剃须刀电
源。(图7)
3 将剃须刀头在皮肤上移动。作直线
和迂回动作。(图8)
注意：仅限在干爽的面部剃须。请勿
将本剃须刀与凝胶、剃须泡沫或水结
合使用。
注意：您的皮肤可能需要2到3周才
能适应飞利浦剃须系统。
4 向下推动开/关滑钮以关闭剃须刀电源。
5 每次剃须后均应清洁剃须刀（请参
阅“清洁和保养”一章）。
6 使用后请盖上剃须刀保护盖，以防
止损坏剃须刀头并避免其内积聚灰
尘。(图9)
-内置充电电池含有可能会污染环境
的物质。丢弃产品时，一定要将电
池取出，并将产品送到官方指定的
回收站。到官方指定的电池回收站
处理电池。如果您在取出电池时遇
到问题，您也可以将产品送至飞利
浦维修中心。维修中心的员工会帮
您取出电池，并以环保的方式处理
它。 (图 28)
卸下充电电池
仅在电池电量完全耗尽后方可取出充
电电池。
1 确保已断开产品的电源连接。
2 让剃须刀一直运行直到停止，
拧开剃须刀背面的螺丝钉(1)
并将后面板从剃须刀上卸除(2)。
(图29)
3 卸下充电电池。(图30)
取出电池之后，不要再将剃须刀与电源
连接在一起。
保修和支持
如果您需要服务或帮助，请访问
www.philips.com/support 或阅读单独的
全球保修卡。
保修条款
由于剃须刀头（刀片和网罩）属于易磨
损物品，因此不在国际保修条款的涵盖
范围之列。
故障种类和处理方法
本章归纳了使用本产品时最常见的一些
问题。如果您无法根据以下信息解决问
题，请访问 www.philips.com/support
查阅常见问题列表，或联系您所在国家/
地区的客户服务中心。
8 清洁后，将刀片重新装回至网罩。
(图21)
9 滑动剃须刀头，将其重新安装到固
定架上。(图22)
10将固定架重新安装到剃须刀头部件
上（可听到“咔嗒”一声）。
(图23)
11 将剃须刀头组件重新安装到剃须刀
上。(图24)
存储
保持器具干燥。
必须在 5°C 至 35°C 之间的温度下使
用和存放本产品。
1 关闭剃须刀。
2 使用后请盖上剃须刀保护盖，
以防止损坏剃须刀头并避免其内积
聚灰尘。(图25)
更换
每两年更换一次刀头以获得最佳的剃
须效果。
只能使用飞利浦剃须刀头（适用于中
国的 HQ4+ 或适用于世界其他各地的
HQ56）更换损坏或磨损的剃须刀头。
有关如何拆卸剃须刀头的说明，请参
阅“清洁和保养”一章中的“每两个
月：清洁剃须刀头”部分。
附件
为了保持剃须刀的最佳性能，请确保定
期清洁并在推荐的时间更换剃须刀头。
剃须刀头
-建议您每两年更换一次剃须刀头。
务必仅使用飞利浦剃须刀头（适用
于中国的 HQ4+ 或适用于世界其他
各地的 HQ56）进行更换。 (图 26)
清洁
-使用飞利浦清洁喷雾剂 (HQ110)
彻底清洁剃须刀头。
环保
-弃置产品时，请不要将其与一般生
活垃圾堆放在一起；应将其交给官
方指定的回收点。这样做有利于环
保。 (图 27)
问题 可能的原因 解决方法
产品
发出
奇怪
的噪
音。
剃须刀头中
积聚了太多
的灰尘。
清洁剃须刀
头。清洁
后，用飞利
浦清洁喷雾
剂 (HQ110) 润
滑网罩内侧的
中央点。请参
阅“清洁和保
养”一章。
剃须刀头已
损坏或磨
损。
更换剃须刀
头。见“更
换”一章。
问题 可能的原因 解决方法
剃须
刀的
剃须
效果
没有
以前
好。
剃须刀头变
脏。您没有
将剃须刀清
洁干净，或
长时间未清
洁过剃须
刀。
在继续剃须之
前，请先彻底
清洗剃须刀。
见“清洁和保
养”一章。
过长的胡须
堵塞了剃须
刀头。
用随附的清
洁刷清洁刀
片和网罩。
见“清洁和保
养”中“每两
个月：剃须刀
头”部分。
剃须刀头已
损坏或磨
损。
更换剃须刀
头。见“更
换”一章。
向上
推动
开/
关滑
钮时
剃须
刀不
工
作。
电池已耗
尽。
给电池充电。
见“充电”一
章。
我在
剃须
后出
现皮
肤过
敏。
您的皮肤需
要一定的时
间来适应飞
利浦剃须
刀。
在前 2-3 周的
使用过程中，
可能会出现皮
肤过敏。在此
之后，皮肤
过敏通常会消
失。
剃须
刀头
的转
速比
平时
慢。
剃须刀头中
积聚了太多
的灰尘。
清洁剃须刀
头。请参阅“
清洁和保养”
一章。
电池已耗尽 给电池充电。
见“充电”一
章。
