Philips PQ218/16 User Manual
Displayed below is the user manual for PQ218/16 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Hair chamber
5 On/off slide
6 Front panel
7 Charging light
8 Foldable plug
9 Release button of foldable plug
10 Retaining frame
11 Central spring of retaining frame
12 Cutter
13 Guard
14 Philips Cleaning Spray (HQ110)
(Optional)
15 Cleaning brush
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Keep the appliance dry.
- This symbol means: Forbidden to clean
under a running tap (Fig. 2).
Warning
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with the
appliance.
Caution
- Use and store the appliance at a
temperature between 5°C and 35°C.
- Only use the cleaning brush supplied.
- Make sure the cleaning brush remains
clean.
Electromagnetic elds (EMF)
This Philips appliance complies with all
standards regarding electromagnetic elds.
If handled properly and according to
the instructions in this user manual, the
appliance is safe to use based on scientic
evidence available today.
Charging
Charge the appliance when the motor
stops or starts running slower.
When you charge the shaver for the rst
time or after a long period of disuse, let it
charge continuously for 12 hours. Charging
normally takes approx. 8 hours.
Do not leave the appliance connected to
the mains for more than 24 hours.
1 Switch off the shaver before you start
charging it.
2 Press the release (1) button and
fold out the foldable plug (2)
(‘click’) (Fig. 3).
3 Insert the foldable plug unit into the
wall socket (Fig. 4).
,The charging light goes on to indicate
that the appliance is charging (Fig. 5).
4 Remove the shaver from the wall
socket when the battery is fully
charged.
5 Press the release button (1) and
fold the foldable plug back into the
appliance (2) (‘click’) (Fig. 6).
Cordless shaving time
A fully charged shaver has a cordless shaving
time of approximately 30 minutes.
Using the appliance
The shaver cannot be used directly from
the mains.
1 Remove the protection cap.
2 Push the on/off slide upwards to
switch on the shaver (Fig. 7).
3 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 8).
Note: Shave on a dry face only. Do not use the
shaver in combination with gel, foam or water.
Note: Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
PQ212, PQ218
Register your product and get support at
www.philips.com/welcome
4222.002.5381.1
1
23 4
56 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
26
27
1
4 Push the on/off slide downwards to
switch off the shaver.
5 Clean the shaver after every
shave, see chapter ‘Cleaning and
maintenance’.
6 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 9).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol
or acetone to clean the appliance.
Clean the shaver after every shave to
guarantee better shaving performance. For
the best cleaning result, we advise you to
use Philips Cleaning Spray (HQ110). Ask
your Philips dealer for information.
Note: Philips Shaving Head Cleaning Spray
(HQ110) may not be available in all countries.
Contact the Customer Care Centre in your
country about the availability of this accessory.
After every shave: shaving
unit and hair chamber
1 Switch off the shaver.
2 Clean the top of the appliance with
the cleaning brush supplied (Fig. 10).
3 Pull the shaving unit straight up off the
shaver (Fig. 11).
4 Clean the inside of the shaving unit
with the cleaning brush (Fig. 12).
5 Clean the hair chamber with the
cleaning brush (Fig. 13).
6 Put the shaving unit back onto the
shaver (Fig. 14).
Every two months: shaving
heads
Note: Do not use cleaning agents or alcohol
to clean the shaving heads. Only use Philips
Cleaning Spray (HQ110).
1 Switch off the shaver.
2 Pull the shaving unit straight up off the
shaver (Fig. 11).
3 To remove the retaining frame,
push the sides of the central spring
towards each other (1).Then lift the
retaining frame out of the shaving unit
(2) (Fig. 15).
4 Slide the shaving heads out of the
retaining frame. Remove and clean
one shaving head at a time. Each
shaving head consists of a cutter and a
guard (Fig. 16).
Note: Do not clean more than one cutter
and guard at a time, since they are matching
sets. If you accidentally mix up the cutters
and guards, it may take several weeks before
optimal shaving performance is restored.
5 Remove the guard from the
cutter (Fig. 17).
6 Clean the cutter with the short-
bristled side of the cleaning brush.
Brush carefully in the direction of the
arrows (Fig. 18).
7 Clean the guard with the long-bristled
side of the cleaning brush (Fig. 19).
8 Put the cutter back into the guard
after cleaning (Fig. 20).
9 Slide the shaving heads back into the
retaining frame (Fig. 21).
10 Put the retaining frame back into the
shaving unit (‘click’) (Fig. 22).
11 Put the shaving unit back onto the
shaver (Fig. 14).
Storage
Keep the appliance dry.
Use and store the appliance at a
temperature between 5°C and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 9).
Replacement
Replace the shaving heads every two years
for optimal shaving results.
Replace damaged or worn shaving heads
with Philips shaving heads only (HQ4+ for
China or HQ56 for the rest of the world).
For instructions on how to remove the
shaving heads, see chapter ‘Cleaning and
maintenance’, section ‘Every two months:
shaving heads’.
Accessories
To retain top performance of your shaver,
make sure you clean it regularly and replace
its shaving heads at the recommended time.
Shaving heads
- We advise you to replace your shaving
heads every two years. Always replace
them with Philips shaving heads only
(HQ4+ for China or HQ56 for the
rest of the world) (Fig. 23).
Cleaning
- Use Philips Cleaning Spray (HQ110) to
clean the shaving heads thoroughly.
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 24).
- The built-in rechargeable battery
contains substances that may pollute
the environment. Always remove the
battery before you discard and hand
in the appliance at an ofcial collection
point. Dispose of the battery at an
ofcial collection point for batteries. If
you have trouble removing the battery,
you can also take the appliance to
a Philips service centre. The staff of
this centre will remove the battery
for you and will dispose of it in an
environmentally safe way (Fig. 25).
Removing the rechargeable
battery
Only remove the rechargeable battery
when it is completely empty.
1 Make sure the appliance is
disconnected from the mains.
2 Let the shaver run until it stops, undo
the screw on the back of the shaver
(1) and lift the back panel off the
shaver (2) (Fig. 26).
3 Remove the rechargeable
battery (Fig. 27).
Do not connect the shaver to the mains
again after you have removed the battery.
Guarantee and service
If you need service or information or if
you have a problem, please visit the Philips
website at www.philips.com or contact
the Philips Consumer Care Centre in your
country. You nd its phone number in the
worldwide guarantee leaet. If there is no
Consumer Care Centre in your country, go
to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below,
contact the Consumer Care Centre in your
country.
Prob-
lem
Possible
cause
Solution
The
shaver
does
not
shave as
well as
it used
to.
The
shaving
heads are
dirty. You
have not
cleaned
the shaver
well
enough
or you
have not
cleaned it
for a long
time.
Clean the shaver
thoroughly
before you
continue shaving.
See chapter
‘Cleaning and
maintenance’.
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the cleaning
brush supplied.
See chapter
‘Cleaning and
maintenance’,
section ‘Every
two months:
shaving heads’.
Prob-
lem
Possible
cause
Solution
The
shaving
heads are
damaged
or worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
The
shaver
does not
work
when I
push the
on/off
slide up-
wards.
The
battery is
empty.
Recharge
the battery.
See chapter
‘Charging’.
My skin
is
irritated
after
shaving.
Your skin
needs time
to get
used to
the Philips
shaving
system.
Skin irritation
during the rst
2-3 weeks of
use is possible.
After this
period, the skin
irritation usually
disappears.
The
rotation
speed
of the
shaving
heads is
slower
than
usual.
Too much
dirt has
collected
in the
shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The
battery is
empty
Recharge
the battery.
See chapter
‘Charging’.
The ap-
pliance
makes a
strange
noise.
Too much
dirt has
collected
in the
shaving
heads.
Clean the
shaving heads.
After cleaning,
lubricate the
central point
on the inside of
the guards with
Philips Cleaning
Spray (HQ110).
See chapter
‘Cleaning and
maintenance’.
6 使用後請為電鬍刀蓋上保護蓋以防
損壞，並避免污垢累積在刀頭中。
(圖9)
清潔與維護
絕對不可使用鋼絲絨、磨蝕性的清潔劑
或侵蝕性的液體(例如汽油或丙酮)清潔
本產品。
在每次刮鬍之後清潔電鬍刀，以保障更
好的刮鬍效果。為達最好的清潔效果，
建議您使用飛利浦噴霧清潔劑 (HQ110)
。請向您的飛利浦經銷商洽詢相關資訊。
注意：飛利浦電鬍刀刀頭噴霧清潔劑
(HQ110)並非所有國家都有供應。關於
是否有這項配件供應，請與您所在國家
的顧客服務中心聯繫。
每次刮鬍後：刮鬍刀組與鬍渣
室
1 請先關閉電鬍刀電源。
2 使用隨附的清潔刷清潔產品上方。
(圖10)
3 從電鬍刀中垂直抽出電鬍刀組。
(圖11)
4 使用隨附的清潔刷清潔刮鬍刀頭組
內部。(圖12)
5 使用清潔刷清潔毛髮收集室。
(圖13)
6 將電鬍刀組裝回電鬍刀上。(圖14)
每兩個月：電鬍刀頭
注意：請勿使用清潔劑或酒精清潔電
鬍刀頭，務必使用飛利浦噴霧清潔劑
(HQ110)。
1 請先關閉電鬍刀電源。
2 從電鬍刀中垂直抽出電鬍刀組。
(圖11)
3 要拆下固定架，請將中央彈簧的兩
側朝中間推壓(1)。然後提起固定架
從電鬍刀組取出(2)。(圖15)
4 將電鬍刀刀頭推出固定架外。一次
取下並清洗一個刀頭。每個電鬍刀
頭都是由刀片和刀網組成。(圖16)
注意：因為刀片及刀網是成對的一組，
請勿一次清潔超過一組。如果您不小心
將刀片及刀網混在一起，可能要花幾週
的時間才能恢復最理想的刮鬍效果。
5 取下刀具的刀網。(圖17)
Prob-
lem
Possible
cause
Solution
The
shaving
heads are
damaged
or worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
繁體中文
簡介
感謝您購買本產品並歡迎加入飛利浦！
請於 www.philips.com/welcome 註冊
您的產品，以善用飛利浦提供的支援。
一般說明 (圖 1)
1 保護蓋
2 電鬍刀刀頭
3 除毛刀頭組
4 毛髮收集室
5 On/Off 開關
6 正面護板
7 充電指示燈
8 折疊式插頭
9 折疊式插頭釋放鈕
10 固定架
11 固定架的中央彈簧
12 刀具
13 刀網
14 飛利浦噴霧清潔劑 (HQ110) (選購)
15 清潔刷
重要事項
使用本產品前，請先仔細閱讀本使用手
冊，並保留說明以供日後參考。
危險
-請保持本產品乾燥。
-此符號表示：禁止在水龍頭下清
洗。 (圖 2)
警示
-基於安全考慮，在缺乏監督及適當
指示之下，本產品不適用於孩童及
任何身體、知覺、或心理功能障礙
者，或缺乏使用經驗及知識者。
-請勿讓孩童使用本產品或將本產品
當成玩具。
警告
-請於 5°C 到 35°C 間使用並存放
本產品。
-只能使用隨附的清潔刷。
-清潔刷請務必保持乾淨。
電磁波 (EMF)
本飛利浦產品符合所有電磁波相關標
準。只要使用方式正確並依照本使用手
冊之說明進行操作，根據現有的科學研
究資料，使用本產品並無安全顧慮。
充電
請在馬達停止轉動時或者運轉速度開始
變慢時，為電鬍刀進行充電。
在您第一次對電鬍刀充電或者長時間未
使用後，請讓其連續充電 12 小時。正
常的充電時間約需 8 個小時。
不要讓電鬍刀連續連接電源插座超過
24小時。
1 開始充電前，請先關閉電鬍刀電
源。
2 按下釋放鈕(1)，然後將將折疊式插
頭往外折(2)(會聽見「喀噠」一聲)
。(圖3)
3 將折疊式插頭裝置插入電源插座。
(圖4)
,充電指示燈亮起，表示產品正在進
行充電。(圖5)
4 當電池完全充滿電後，請將電鬍刀
拔離電源插座。
5 按下釋放鈕(1)並將折疊式插頭折
回產品中(2)(會聽見「喀噠」一聲)
。(圖6)
無線刮鬍時間
電池充滿的電鬍刀可不插電刮鬍約
30 分鐘。
使用此產品
電鬍刀無法直接插電使用。
1 卸下保護蓋。
2 將On/Off開關往上推，即可開啟電
鬍刀電源。(圖7)
3 將電鬍刀頭在皮膚上移動，請同時
用直線及畫圓的方式來移動。
(圖8)
注意：僅可乾刮。使用電鬍刀時，請勿
搭配凝露、泡沫或水。
注意：您的皮膚可能需要2到3週的
時間才能完全適應飛利浦電鬍刀系統。
4 將On/Off開關往下推，即可關閉電
鬍刀電源。
5 每次刮鬍後，請清潔本電鬍刀，請
參閱「清潔與保養」單元。
環境保護
-本產品使用壽命結束時請勿與一般
家庭廢棄物一併丟棄。請將該產品
放置於政府指定的回收站，此舉能
為環保盡一份心力。 (圖 24)
-本產品內建的充電式電池含有可能
會污染環境的物質。丟棄本產品
或是將本產品放到政府指定回收站
前，請務必先取出電池，並且將電
池送到政府指定的電池回收站。若
您無法取出電池，可將本產品拿到
飛利浦服務中心，服務中心的人員
會為您卸下電池，並以對環境無害
的方式處理電池。 (圖 25)
取出充電電池
必須將充電式電池電力完全耗盡後才能
拆卸電池。
1 請確實拔除產品電源插頭。
2 讓電鬍刀持續運轉直到完全停止，
轉開電鬍刀背面的螺絲(1)，然後打
開電鬍刀的背面模板(2)。(圖26)
3 取出充電電池。(圖27)
卸除電池後，請勿再次將電鬍刀連接
至電源。
保固與服務
如需相關服務或資訊，或是有任何
問題，請瀏覽飛利浦網站，網址
為：www.philips.com，或聯絡您所在
國家/地區的飛利浦客戶服務中心，電話
號碼可參閱全球保證書。若您的所在國
家/地區沒有客戶服務中心，請洽詢當地
的飛利浦經銷商。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損
性，因此不在全球保固範圍內。
故障排除
本說明概述您使用本產品時最常遇到的
問題。如果您無法利用以下資訊解決您
遇到的問題，請聯絡您所在國家/地區的
客戶服務中心。
6 請使用清潔刷的短毛側來清潔刀
具。請依箭頭方向小心刷動。
(圖18)
7 請使用清潔刷的長毛側來清潔刀
網。(圖19)
8 清潔後，將刀具放回刀網中。
(圖20)
9 將電鬍刀刀頭推回固定架中。
(圖21)
10 將固定架裝回電鬍刀組(會聽見「
喀噠」一聲)。(圖22)
11 將電鬍刀組裝回電鬍刀上。(圖14)
收納
請保持本產品乾燥。
請於 5°C 到 35°C 間使用並存放本
產品。
1 請先關閉電鬍刀電源。
2 使用後請為電鬍刀蓋上保護蓋以防
損壞，並避免污垢累積在刀頭中。
(圖9)
更換
每隔兩年更換一次電鬍刀頭，以確保維
持最佳的刮鬍效果。
損壞或用舊的刀頭限以飛利浦電鬍刀
刀頭替換 (中國為 HQ4+，其他國家為
HQ56)。
有關如何取下電鬍刀頭的說明，請參閱
「清潔與維護」單元之「每兩個月：電
鬍刀頭」章節。
配件
若要維持電鬍刀的最佳效能，請務必定
期清潔電鬍刀，並於建議的時間更換電
鬍刀刀頭。
電鬍刀刀頭
-建議您每兩年即更換電鬍刀刀頭。
限以飛利浦電鬍刀刀頭替換 (中國
為 HQ4+，其他國家為 HQ56)。
(圖 23)
清潔
-使用飛利浦噴霧清潔劑 (HQ110) 徹
底清潔電鬍刀頭。
問題 可能原因 解決方法
產品發
出奇怪
的噪
音。
過多污垢
累積在刀
頭中。
請清潔電鬍刀
刀頭。清潔
後，請使用飛
利浦噴霧清潔
劑 (HQ110) 潤
滑刀網內側的
中心點。請參
閱「清潔與維
護」單元。
電鬍刀刀
頭毀壞或
磨損。
更換電鬍刀刀
頭。請參閱「
更換」單元。
問題 可能原因 解決方法
電鬍刀
不像平
常一樣
運作。
電鬍刀刀
頭不潔。
電鬍刀清
潔不夠徹
底或是太
久沒有清
潔。
在您繼續刮鬍
之前，請徹底
清潔電鬍刀。
請參閱「清潔
與維護」單
元。
長鬍鬚卡
住電鬍刀
刀頭。
請使用隨附的
毛刷清潔刀具
及刀網。請參
閱「清潔與維
護」單元之「
每兩個月：電
鬍刀刀頭」小
節。
電鬍刀刀
頭毀壞或
磨損。
更換電鬍刀刀
頭。請參閱「
更換」單元。
將 on/
off 開
關往上
推，但
電鬍刀
不動。
電池電量
完全耗
盡。
為電池充電。
請參閱「充
電」單元。
刮鬍之
後，皮
膚感到
刺痛。
您的皮膚
需要一些
時間才能
適應飛利
浦電鬍刀
系統。
開始使用的第
2 到 3 週，皮
膚可能會有過
敏現象。過了
這段時間，皮
膚過敏的症狀
通常會消失。
刀頭的
旋轉速
度比平
常緩
慢。
過多污垢
累積在刀
頭中。
請清潔電鬍刀
刀頭。請參閱
「清潔與維
護」單元。
電池電量
完全耗盡
為電池充電。
請參閱「充
電」單元。